To Next PageTo Next PageWhy does my LG HT353SD-A2 remote control not work properly?
If your LG Receiver remote control isn't working correctly, ensure you're pointing it directly at the receiver's remote sensor. Try using the remote within 23 ft (7 m). Remove any obstacles between the remote and the receiver. If it still doesn't work, replace the batteries with new ones.
What to do if there is no sound from my LG HT353SD-A2?
If you're experiencing no sound or very low sound from your LG Receiver, make sure the equipment connected with the audio cable is set to receive DVD audio by selecting the correct input mode. Also, ensure the audio cables are securely connected. Verify that the connected equipment is powered on, and if the audio cable is damaged, replace it.
How to troubleshoot no power on my LG HT353SD-A2 Receiver?
If your LG Receiver has no power, ensure the power cord is securely plugged into the wall outlet.
How to fix LG HT353SD-A2 if it does not start playback?
If your LG Receiver isn't starting playback, first ensure that a playable disc is inserted correctly, with the playback side down and placed within the guide. If a menu is on the TV screen, press the SETUP button to turn it off. Also, ensure that the Rating level is not set, or change it. Check that the DVD or audio CD indicator in the DVD display is lit.
Why is there no picture from my LG HT353SD-A2?
If you're not getting a picture from your LG Receiver, first ensure your TV is set to receive the DVD signal. Check that the video cable is securely connected to the jacks. Also, make sure your connected TV is turned on.
How to eliminate loud hum or noise from LG HT353SD-A2?
If you hear a loud hum or noise from your LG Receiver, clean the disc first. Ensure the speakers and components are securely connected. If the issue persists, move your TV away from the audio components.
Why can't I tune into radio stations on my LG HT353SD-A2?
If you cannot tune into radio stations on your LG Receiver, ensure the antenna is securely connected and positioned correctly. If the signal strength is weak, try tuning in the station manually. Note that you may need to preset the stations.
How to fix the dim front panel display on my LG HT353SD-A2 Receiver?
To brighten a dim front panel display on your LG Receiver, press SLEEP(Dimmer) on the remote control.
General| Type | Home Theater System |
|---|---|
| Number of Channels | 5.1 |
| DVD Playback | Yes |
| HDMI Inputs | 1 |
| USB Playback | Yes |
| Bluetooth | No |
| Supported Media | DVD, CD, USB |
| Audio Formats | Dolby Digital, DTS |
| Connectivity | USB |
| Video Formats | MPEG2, DivX |
| Inputs | HDMI, USB |
| Outputs | HDMI |
Notes regarding careful handling of the pick-up, including transport, repair, and cleaning procedures.
Precautions for handling components, tools, and the workbench during CD player repairs.
Techniques to reduce component damage caused by static electricity, including handling procedures and precautions.
Explanation of graphic symbols used to indicate dangerous voltage and important safety information.
Procedure for detecting and updating EEPROM data for DVD part using remote control inputs.
Procedure for detecting and updating EEPROM data for Amplifier part using remote control inputs.
Instructions for updating Audio MICOM and DVD programs via CD or USB.
Technical specifications for the DVD/CD Receiver, including power, speakers, and dimensions.
Flowchart for diagnosing power supply and playback issues, guiding service personnel through checks.
Diagnostic steps for front panel circuits, including LED, Digitron, buttons, and remote control.
Continued diagnostic steps for front panel circuits, focusing on power and MICOM connections.
Diagram illustrating the sequence of operations from power on to disc loading and playback.
Flowchart for testing power PCB, DC outputs, FLASH updates, and related circuits.
Continues system test flow, checking Flash Memory, SDRAM, video outputs, and tray control signals.
Continues system test flow, checking SLED movement, motor drivers, and focus signals.
Continues system test flow, checking laser operation, disc ID, spindle rotation, and RF signals.
Continues system test flow, checking focus, tracking, and disc playback signals.
Final steps in system test flow, checking audio output and PWM IC status.
Troubleshooting steps for "PROTECTION" message on the FLD, checking IC and transistor status.
Flowchart for diagnosing audio and MICOM circuit issues, checking various inputs and IC status.
Details and waveforms for system test signals, including 27MHz clock and reset signals.
Waveforms and details for SDRAM clock and Flash R/W enable signals during download.
Waveforms illustrating tray open and close signals, with associated circuit diagrams.
Waveforms for SLED control signals under no-disc conditions, with related IC pinouts.
Waveforms for lens control signals under no-disc conditions, with related IC pinouts.
Waveforms for judging disc type (DVD and CD), with associated circuit diagrams.
Waveforms illustrating disc type judgement for CD playback.
Waveforms showing focus signals during DVD and CD playback, with related IC pinouts.
Waveforms for spindle control signals under no-disc conditions, with related IC pinouts.
Waveforms for MT1389/L video output signals, including composite and Y signals.
Waveforms for audio output signals from the MT1389/L chip, including related signals.
Waveforms for DVD and amplifier circuits, showing signal transitions between specific points.
Block diagram and pin configuration for IC501 (MT1389L).
Detailed block diagram of the MT1389L MPEG chip, showing its main functional blocks.
Detailed pin descriptions for IC501 (MT1389L), explaining each pin's function and interface.
Continued pin descriptions for IC501, covering pins 100 onwards, including audio DAC and GPIO functions.
Continued pin descriptions for IC501, covering DRAM interface and microcontroller pins.
Continued pin descriptions for IC501, covering DRAM addresses, GPIO, and control signals.
Continued pin descriptions for IC501, covering GPIO, SPDIF, and other interface pins.
Pin configuration and block diagram for the IC401 motor driver.
Detailed pin descriptions for IC401, explaining its functions for focus, sled, tray, spindle, and tracking drivers.
Pin configuration for the IC101 Microcomputer (MICOM).
Block diagram of the IC101 Microcomputer, showing its internal modules and interfaces.
Pin descriptions for IC101, covering power supply, Port 0, Port 1, and Port 2 functions.
Continued pin descriptions for IC101, covering Port 7, Port 8, Port 3, Port C, and reset/crystal pins.
Pin configuration for the IC201 ADC (CS5345).
Block diagram of the IC201 ADC (CS5345), showing its analog inputs and digital interfaces.
Detailed pin descriptions for IC201 ADC, covering serial control, analog inputs, and digital grounds.
Pin configuration for the IC704 PWM chip.
Pin descriptions for IC704 PWM, covering power, PCM, and PWM audio outputs.
Continued pin descriptions for IC704 PWM, covering system control interfaces and test modes.
Continued pin descriptions for IC704 PWM, covering special control interfaces and test modes.
Diagram showing the main PCB, SMPS PCB, Front PCB, and Mic&USB PCB connections.
High-level block diagram of the entire system, showing major components and their interconnections.
SMPS (Power) circuit diagram, detailing the power supply components and layout.
Circuit diagram for the MPEG section, showing connections to IC501 (MT1389L) and other components.
Circuit diagram for the servo section, detailing motor drivers and pickup connections.
Circuit diagram for the MICOM section, showing connections to IC101 and other peripheral interfaces.
Circuit diagram for the I/O section, including SCART, RCA, and tuner interfaces.
Circuit diagram for the amplifier section, showing PWM modulation and audio output stages.
Circuit diagram for the microphone input section.
Circuit diagram for the front panel, including display, volume control, and buttons.
Circuit diagram for the power key and standby LED.
Circuit diagram for MIC, USB, and PTB connections, including optional configurations.
Top view diagram of the main PCB.
Bottom view diagram of the main PCB.
Diagram of the SMPS (Switch Mode Power Supply) PCB.
PCB diagrams for the Timer board for HT303 and HT353.
Exploded view showing the main chassis, front panel, and internal components assembly.
Exploded view of the deck mechanism, with a parts list and specifications.
Diagram illustrating the packing accessories included with the unit.
Exploded view and parts list for the SH33SU satellite speakers.
Exploded view and parts list for the SH33SD-S satellite speakers.
Exploded view of the passive subwoofer, showing its components.
Overview of deck mechanism parts locations, with references to specific pages for details.
Detailed listing of deck mechanism parts and their fixing types, organized by view.
Step-by-step instructions for disassembling the main base and tray disc.
Disassembly steps for the base assembly sled, gear feed, gear middle, gear rack, and rubber rear.
Disassembly and reassembly steps for frame assembly, belt loading, gear pulley, gear loading, and guide.
Comprehensive exploded view of the deck mechanism, illustrating all sub-assemblies and parts.
