Linde T 16 - Before Operation Procedures; Safety Rules and Definitions

3
6
0
8
0
4
2
5
1
1
-
0
5
0
4
Use of materials
Materials must always be used in conformity with the
instructions supplied by the manufacturer.
Materials must be stored only in regulation containers,
and only in the locations designated for this purpose.
Ingredients may be flammable, and must therefore not be
placed in contact with any flame or hot object.
Use only the proper receptacles for draining liquids.
Observe any safety and recycling recommendations
provided by the manufacturer of the material or cleaning
product concerned.
Avoid any spillage of
materials.
Use absorbent materials
to clean any floor spillage, and recycle such materials
correctly.
Old or exhausted materials must be recycled in conformity
with regulations.
Comply with legal regulations.
Clean the parts concerned before carrying out lubrication,
changing filters, or working on the hydraulic system.
Any worn-out parts removed must be recyc
led in conformity
with regulations for protection of the environment.
CAUTION
Accidental penetration of pressurised hydraulic
fluid under the skin is dangerous. In the event of
injury, consult a doctor immediately.
CAUTION
Incorrect handling of cooling products or addi-
tives is hazardous to health and to the
environment.
Definition of terms relating to safety
The terms DANGER, CAUTION, ATTENTION and NOTE
are used in this manual to indicate a particular risk or to
give any special information which requires attention:
DANGER
Meaning: Non-observance entails the risk of
death, or of serious material damage.
CAUTION
Meaning: Non-observance entails the risk of
serious injury, and/or serious material damage.
ATTENTION
Meaning: Non-observance entails the risk of
deterioration or destruction of the equipment.
NOTE
Meaning: Special attention must be paid to a particular
technical point which may not be immediately obvious,
even to an expert.
Safety rules
This instruction manual, and the VDMA booklet “Directive
s
governing the use of handling trucks in conformity with
specifications and regulations” supplied with the truck,
must be given to the relevant persons, a
nd in particular to
personnel responsible for driving and servicing the truck.
The employer must ensure that the truck operator has
properly understood this information, particularly in rela-
tion to safety.
Please comply with the enclosed directives and safety
rules, with particular regard to the following:
-
Inf
orm
ati
on reg
ard
ing th
e use of h
and
lin
g truc
ks.
-
Reg
ulat
ions re
gard
ing tr
aff
ic lan
es and wo
rkin
g area
.
-
Dri
ving co
ndu
ct, and th
e drive
r’s rig
hts and ob
liga
tio
ns.
-
Us
e in
spe
cia
l en
vi
ron
me
nt
s.
-
Inf
orm
ati
on rega
rdin
g start
ing
, drivi
ng and brak
ing
.
-
Inf
orm
ati
on rega
rdi
ng mai
nten
ance a
nd rep
air.
-
Reg
ular
chec
ks an
d te
chni
cal
insp
ect
ions
.
-
Rec
ycli
ng o
f gr
eas
es,
oils
and
bat
teri
es.
-
Re
si
du
al h
az
ar
ds
.
It is recommended that both the user and the person in
charge (employer) take care to comply with all safety rules
regarding the use of handling trucks.
During the instruction of truck operators, particular
emphasis should be placed on the following points:
-
spec
ial c
hara
cter
ist
ics o
f th
e tru
ck,
-
sp
ec
ia
l
ac
ce
ss
ori
es,
-
spec
ial
fea
ture
s of
the
work
plac
e.
The user should be trained in driving and mast manoeu-
vres until the truck is fully under control.
Then, and only then, should pallets be moved or stac
ked.
The stability of the lift-truck is guaranteed when used
correctly. If, in the event of improper use or driver err
or, the
truck shows any tendency to overbalance, it is essential
that the instructions below are followed.
Before operation
https://www.besttruckmanuals.com/