What to do if LEVEL reading is correct but LOOP is stuck at 4 mA on Magnetrol Transmitter?
If the LEVEL reading on the Display is correct, but the LOOP is stuck on 4 mA, the basic configuration data might be questionable. Set the POLL ADR to 0 if you are not using HART multi-drop.
Why are LEVEL readings on Magnetrol Measuring Instruments consistently inaccurate?
If LEVEL readings are consistently high or low by a fixed amount, the configuration data might not accurately match the probe length or tank height. Ensure the proper Probe Model, Level Offset, or probe length is configured. You can also adjust the trim level value by the amount of noted inaccuracy.
What to do if the LEVEL reading is stuck at full scale on Magnetrol eclipse 705?
If the LEVEL reading on the display is stuck at full scale, the software might believe the probe is flooded. Check the actual level. If the probe isn't flooded, inspect for buildup or obstructions near the top of the probe. You may also select a higher dielectric range, check for condensation in the probe connection, or add Blocking Distance.
What does 'LVL < Probe Length' mean on Magnetrol Transmitter?
If 'LVL < Probe Length', the apparent position of the upper level pulse is beyond the end of the probe. Check the entered probe length and change the threshold to fixed.
What does it mean when EOP is less than probe length on Magnetrol Transmitter?
If the EOP (End of Probe) is less than the Probe Length, the End of Probe signal from a dry probe is out of range. Ensure the probe length is entered correctly. Also, set the transmitter to a lower dielectric range and ensure proper blocking distance.
What does 'FidShift' mean on Magnetrol Transmitter and how can I resolve it?
If you see 'FidShift', it means the FidTicks have shifted from the expected value. Check the connection between the probe and the transmitter, check for moisture on top of the probe, and check for a damaged gold pin on the high-frequency connector.
How to resolve 'Lo Temperature' warning on Magnetrol eclipse 705 Measuring Instruments?
If the present temperature in the electronics compartment is below -40°F (-40°C), the transmitter may need to be moved to ensure the ambient temperature is within specification, or change to a remote transmitter.
How to fix inaccurate LEVEL, % OUTPUT, and LOOP values on Magnetrol Transmitter?
If the LEVEL, % OUTPUT, and LOOP values are all inaccurate, the basic configuration data might be questionable. Try reconfiguring the Probe Model, Probe Mount, Probe Length, or Level Offset. Also, ensure the Level is accurate and verify the 4 mA and 20 mA Loop values.
What does 'Fid Sprd' mean on Magnetrol Transmitter, and what steps should I take to correct it?
If you see 'Fid Sprd', it means the Fiducial Ticks variation is excessive. Check the connection between the probe and the transmitter and check for moisture on top of the probe.
Why is the LEVEL value reading high when it should be zero on Magnetrol eclipse 705 Measuring Instruments?
If the LEVEL value is reading high when it should be zero, the transmitter might be loose or disconnected from the probe. Ensure the transmitter is securely connected to the probe.
Prerequisites and initial steps for installation.
Procedures for mounting the transmitter and probe.
Steps for making electrical connections.
Basic setup and configuration of the transmitter.
Procedures for safely unpacking the instrument.
Safety guidelines for handling sensitive electronic components.
Preparatory checks and considerations before installation.
Details on probe and transmitter mounting procedures.
Specific steps for installing coaxial probes.
Specific steps for installing twin rod probes.
Specific steps for installing single rod probes.
Procedures for attaching the transmitter unit.
Electrical connection procedures.
Wiring instructions for general purpose installations.
Wiring requirements for intrinsically safe installations.
Wiring procedures for explosion-proof environments.
Setup and calibration procedures.
Details on using the transmitter's interface and controls.
Detailed configuration steps for the Model 705 menu.
Configuration steps for level-only measurement.
Configuration for level and volume measurement.
Configuration for interface level measurement.
Explanation of the Level Offset parameter.
Procedure for linearizing output for odd-shaped vessels.
Setup and communication via HART.
How to connect a HART communicator.
Overview of the HART communicator's display menu.
Details on integrating with Fieldbus systems.
Overview of FOUNDATION fieldbus system.
Configuration steps for Fieldbus devices.
General overview of the ECLIPSE Level Transmitter.
Explanation of the technology and principles.
Explanation of the MIR technology.
How the device detects interface levels.
Diagnosing and resolving common problems.
Common system issues and their solutions.
Interpreting diagnostic messages and status indicators.
Certifications and compliance standards.
Information on replacement and spare parts.
List of components available for replacement.
Technical details and performance data.
Functional characteristics and parameters.
Performance metrics and accuracy details.
Physical dimensions and mounting information.
Product identification codes.
Breakdown of transmitter model number codes.
Breakdown of probe model number codes.
Details on warranty, repairs, and service.
Steps for returning materials for service or repair.
General| Brand | Magnetrol |
|---|---|
| Model | eclipse 705 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
