How to stabilize fluctuating LEVEL and % OUTPUT values on Magnetrol eclipse 705?
If the LEVEL and % OUTPUT values are fluctuating, it could be due to turbulence. To stabilize the readings, increase the Damping factor.
How to troubleshoot 'EOP High' error on Magnetrol Measuring Instruments?
If the End of Probe signal is out of range, ensure the Probe Length is entered correctly.
How to resolve 'Lvl
If the apparent position of the upper level pulse is beyond the end of the probe, check the entered Probe Length and change the Threshold to Fixed.
How to troubleshoot 'No Fiducial' error on Magnetrol eclipse 705 Measuring Instruments?
If the fiducial signal is not being detected, check the connection between the probe and the transmitter. Also, check for moisture on top of the probe and for a damaged gold pin in the high-frequency connector.
What does 'May be Flooded' mean on Magnetrol eclipse 705 and how to resolve it?
If there is a loss of level signal possibly due to flooding (Twin Rod probes only), decrease the level in the vessel. You can also set the Dielectric to a lower range value or replace it with a Model 7xR Overfill probe.
What does 'High Volume Flt' mean on Magnetrol Measuring Instruments and how can it be fixed?
If the level is more than 5% above the highest point in the strapping table, verify the strapping table is entered correctly. The signal amplitude may also be lower than desired.
How to resolve 'Hi Temperature' warning on Magnetrol eclipse 705 Measuring Instruments?
If the present temperature in the electronics compartment is above 80°C, the transmitter may need to be moved to ensure the ambient temperature is within specification, or change to a remote mount transmitter.
How to resolve 'Lo Temperature' warning on Magnetrol eclipse 705 Measuring Instruments?
If the present temperature in the electronics compartment is below -40°F (-40°C), the transmitter may need to be moved to ensure the ambient temperature is within specification, or change to a remote transmitter.
How to fix inaccurate LEVEL, % OUTPUT, and LOOP values on Magnetrol Transmitter?
If the LEVEL, % OUTPUT, and LOOP values are all inaccurate, the basic configuration data might be questionable. Try reconfiguring the Probe Model, Probe Mount, Probe Length, or Level Offset. Also, ensure the Level is accurate and verify the 4 mA and 20 mA Loop values.
What to do if LEVEL, % OUTPUT, and LOOP values fluctuate on Magnetrol Transmitter?
If the LEVEL, % OUTPUT, and LOOP values are fluctuating, it might be due to turbulence. Increase the Damping factor until the readings stabilize.
Prerequisites and initial steps for installation.
Procedures for mounting the transmitter and probe.
Steps for making electrical connections.
Basic setup and configuration of the transmitter.
Procedures for safely unpacking the instrument.
Safety guidelines for handling sensitive electronic components.
Preparatory checks and considerations before installation.
Details on probe and transmitter mounting procedures.
Specific steps for installing coaxial probes.
Specific steps for installing twin rod probes.
Specific steps for installing single rod probes.
Procedures for attaching the transmitter unit.
Electrical connection procedures.
Wiring instructions for general purpose installations.
Wiring requirements for intrinsically safe installations.
Wiring procedures for explosion-proof environments.
Setup and calibration procedures.
Details on using the transmitter's interface and controls.
Detailed configuration steps for the Model 705 menu.
Configuration steps for level-only measurement.
Configuration for level and volume measurement.
Configuration for interface level measurement.
Explanation of the Level Offset parameter.
Procedure for linearizing output for odd-shaped vessels.
Setup and communication via HART.
How to connect a HART communicator.
Overview of the HART communicator's display menu.
Details on integrating with Fieldbus systems.
Overview of FOUNDATION fieldbus system.
Configuration steps for Fieldbus devices.
General overview of the ECLIPSE Level Transmitter.
Explanation of the technology and principles.
Explanation of the MIR technology.
How the device detects interface levels.
Diagnosing and resolving common problems.
Common system issues and their solutions.
Interpreting diagnostic messages and status indicators.
Certifications and compliance standards.
Information on replacement and spare parts.
List of components available for replacement.
Technical details and performance data.
Functional characteristics and parameters.
Performance metrics and accuracy details.
Physical dimensions and mounting information.
Product identification codes.
Breakdown of transmitter model number codes.
Breakdown of probe model number codes.
Details on warranty, repairs, and service.
Steps for returning materials for service or repair.
General| Brand | Magnetrol |
|---|---|
| Model | eclipse 705 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
