Mitsubishi FREQROL-E700

App.1-5
Appendix
Parameter Name Setting range Initial value
342
Communication
EEPROM write
selection
0, 1 0
343
Communication
error count
— 0
450
Second applied
motor
0, 1, 9999 9999
495
Remote output
selection
0, 1, 10, 11 0
496
Remote output data 1 0 to 4095 0
497
Remote output data 2 0 to 4095 0
502
Stop mode selection
at communication
error
0, 1, 2, 3 0
503 Maintenance timer 0 (1, 9998) 0
504
Maintenance timer
alarm output set
time
0 to 9998,
9999
9999
547
USB communication
station number
0 to 31 0
548
USB communication
check time interval
0 to 999.8s
9999
9999
549 Protocol selection 0, 1 0
550
NET mode
operation command
source selection
0, 2, 9999 9999
551
PU mode operation
command source
selection
2 to 4, 9999 9999
555
Current average
time
0.1 to 1.0s 1s
556
Data output mask
time
0 to 20s 0s
557
Current average
value monitor signal
output reference
current
0 to 500A
Inverter
rated
current
563
Energization time
carrying-over times
(0 to 65535) 0
564
Operating time
carrying-over times
(0 to 65535) 0
571
Holding time at a
start
0 to 10s, 9999 9999
611
Acceleration time at
a restart
0 to 3600s,
9999
9999
653
Speed smoothing
control
0 to 200% 0
665
Regeneration
avoidance
frequency gain
0 to 200% 100
800
Control method
selection
20, 30 20
Parameter Name Setting range Initial value
859 Torque current
0 to 500A
(0 to ****),
9999
*5
9999
872
*8
Input phase loss
protection selection
0, 1 1
882
Regeneration
avoidance operation
selection
0, 1, 2 0
883
Regeneration
avoidance operation
level
300 to 800V
400VDC/
780VDC *4
885
Regeneration
avoidance
compensation
frequency limit value
0 to 10Hz,
9999
6Hz
886
Regeneration
avoidance voltage
gain
0 to 200% 100%
888 Free parameter 1 0 to 9999 9999
889 Free parameter 2 0 to 9999 9999
C0
(900)
*7
FM terminal
calibration
— —
C2
(902)
*7
Terminal 2
frequency setting
bias frequency
0 to 400Hz 0Hz
C3
(902)
*7
Terminal 2
frequency setting
bias
0 to 300% 0%
125
(903)
*7
Terminal 2
frequency setting
gain frequency
0 to 400Hz 60Hz
C4
(903)
*7
Terminal 2
frequency setting
gain
0 to 300% 100%
C5
(904)
*7
Terminal 4
frequency setting
bias frequency
0 to 400Hz 0Hz
C6
(904)
*7
Terminal 4
frequency setting
bias
0 to 300% 20%
126
(905)
*7
Terminal 4
frequency setting
gain frequency
0 to 400Hz 60Hz
C7
(905)
*7
Terminal 4
frequency setting
gain
0 to 300% 100%
C22
(922)
*6 *7
Frequency setting
voltage bias
frequency (built-in
potentiometer)
0 to 400Hz 0
C23
(922)
*6 *7
Frequency setting
voltage bias (built-in
potentiometer)
0 to 300% 0