NAD C375BEE - User Manual

Other manuals for NAD C375BEE

Datasheet4 pages

Questions and Answers

S
Shannon WhiteJul 26, 2025
Why is there no sound coming from my NAD Amplifier?
- M
  Mary RichJul 26, 2025
  There are several reasons why your NAD Amplifier might not be producing sound: * The AC power lead might be unplugged, or the power might not be switched on. Ensure the AC lead is properly plugged in and the power is switched ON. * The Tape Monitor mode might be selected. De-select Tape Monitor mode. * The Mute function might be activated. Switch off Mute. * The rear Pre-out/Main-in amp links might not be fitted. Fit the links.
A
Andrew Navarro DVMJul 31, 2025
What to do if my NAD Amplifier Standby LED turns red during operation?
- J
  Jill MortonJul 31, 2025
  If the Standby LED on your NAD Amplifier turns red during operation, it indicates a problem. This could be due to: * The unit has overheated. Turn the unit OFF and ensure that the ventilation slots on the top and bottom are not blocked. After the unit has cooled down, turn it back ON. * The overall impedance of the loudspeakers is too low. Ensure the overall loudspeaker impedance is not below 4 ohms.
S
smithtimothyAug 7, 2025
How to fix a NAD Amplifier remote control that is not working?
- H
  humphreycoreyAug 7, 2025
  If your NAD Amplifier remote control handset is not working, consider the following: * The battery might be flat or incorrectly inserted. Check or replace the battery. * The IR transmitter or receiver windows might be obstructed. Remove any obstruction. * The IR receiver might be in direct sunlight or very bright ambient light. Place the unit away from direct sun and reduce the amount of ambient light.
K
Kathryn StevensAug 13, 2025
What to do if there is no sound in one channel of my NAD Amplifier?
- K
  Kevin WardAug 13, 2025
  If you're experiencing a lack of sound in one channel of your NAD Amplifier, here are a few things to check: * The balance control might not be centered. Make sure the balance control is centered. * The speaker might not be properly connected or could be damaged. Check the connections and the speaker itself. * The input lead could be disconnected or damaged. Inspect the leads and connections.
D
Dawn NashAug 19, 2025
Why does my NAD Amplifier have weak bass or a diffused stereo image?
- A
  Amy RollinsAug 19, 2025
  If your NAD Amplifier is producing weak bass or a diffused stereo image, it might be due to the speakers being wired out of phase. Check the connections to all speakers in the system.

Summary

Important Safety Instructions

Caution Regarding Placement

Ensure adequate space around the unit for proper ventilation.

Getting Started

Unpacking and Setup

Details on what's in the box and initial setup steps.

Bare Wires and Pin Connectors

Instructions for connecting speaker wires and pin connectors.

Quick Start

Step-by-step guide for initial setup and basic operation.

Identification of Controls

Front Panel

Overview of the amplifier's front panel controls and indicators.

Input Selectors

Selection of audio sources for the amplifier.

Tone Defeat

Tone Controls

Balance Control

Volume Control

Rear Panel

Overview of the amplifier's rear panel connections and ports.

Rear Panel Connections and Features

Detailed descriptions of all rear panel inputs, outputs, and features.

Pre Out Connections

Details on PRE OUT 1, PRE OUT 2, and VOLUME PRE OUT 2 controls.

Bridge Mode

Configuration for mono operation, doubling output power.

Soft Clipping and PowerDrive

Speaker Terminals and AC Mains Input

Power Switch, Switched Outlet, and Fuse Holder

SR 8 Remote Control

Description and operation of the SR 8 remote control handset.

Remote Control Functions

Detailed explanation of remote control buttons and their functions.

Volume and Speaker Selection

Tone Controls and CD Player Functions

Tuner Control Functions

Reference

Troubleshooting

Common issues and their possible solutions.

Specifications

Technical specifications for amplifier sections and I/O.

Overall Specifications

PP 375 Phono Preamplifier MDC Module

Features

Specifications

MDC DAC Modular Design Construction Digital-to-Analog Converter

Optical Input

DAC Module Input Selector

USB Input

NAD C375BEE Specifications

General

Power Output	150W (8 Ohms)
Total Harmonic Distortion	0.009% (20Hz-20kHz)
Frequency Response	20Hz-20kHz
Dimensions	435 x 150 x 380mm (W x H x D)
THD	<0.03% (20Hz-20kHz)
IMD	<0.03%
Clipping Power	180W (8 Ohms)
Input Impedance	47k Ohms
Damping Factor	>200 (ref. 8 Ohms, 50Hz and 1kHz)