To Next Page

To Previous Page

5. Using On-Screen Menu

[Standby mode]

Set power consumption in standby mode, no matter whenever your projector is operated through network.

1) Press ▲ ▼ button to select [Standby mode] menu.

2) Press <ENTER> button.

3) Press ▲ ▼ button to adjust levels.

Normal......Some function will be disabled once your projector is in ECO. standby mode to reduce power consumption.

network and RS-232C serial communication will be unavailable except the power on command during that mode.

Network standby......In order to reduce power consumption, some functions in standby mode will be limited. Under

network standby, network function is not available and RS-232C serial communication (except boot command)

function is not available.

• Standby mode network wake-up function can only use the "Wake On LAN" tool.

Sleep ........Even in standby mode,there are no restraint on network function and serial communication function.

On start

HDMI setup

Setting

Standby mode

High altitude

ECO mode

Cooling fast

Closed caption

Key lock

lris

Baud rate

Sound

Off

Normal

Off

Normal

Off

19200

[High altitude]

You can change the setting about speed of cooling fan according to the altitude your projector is operating at.

1) Press ▲ ▼ button to select [High altitude] menu.

2) Press <ENTER> button.

3) Press ▲ ▼ button to select required menu.

Off: Normal speed. set the option off when operating the operator, if the altitude is not too high.

On: Faster than when in off mode .set the option on when operating the operator in high land.

Note:

• Set high altitude option on when you operate the operator at an altitude of approximately 1700 m/5500 f or higher.

On start

HDMI setup

Setting

Standby mode

High altitude

ECO mode

Cooling fast

Closed caption

Key lock

lris

Baud rate

Sound

Off

Normal

Off

Normal

Off

19200

Questions and Answers:

Need help?

Do you have a question about the NEC MC453X and is the answer not in the manual?

NEC MC453X Specifications

General

Native aspect ratio	4:3
Projection distance	0.9 - 10.9 m
Vertical scan range	50 - 120 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	16000:1
Screen size compatibility	30 - 300 \
Projector native resolution	XGA (1024x768)
Keystone correction, horizontal	-30 - 30 °
RMS rated power	16 W
Number of built-in speakers	1
Placement	Ceiling, Floor
Product type	Standard throw projector
Product color	White
Cable lock slot type	Kensington
Lamp power	240 W
Lamps quantity	1 lamp(s)
Light source type	Lamp
Lamp power (economic mode)	150 W
Service life of light source	10000 h
Service life of light source (economic mode)	20000 h
Built-in display	-
Focus	Manual
Throw ratio	1.5 - 1.8:1
Focal length range	19.158 - 23.018 mm
Aperture range (F-F)	1.6 - 1.76
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	320 W
Power consumption (standby)	0.5 W
Power consumption (typical)	305 W
Power consumption (economy mode)	215 W
Power consumption (network standby)	2 W
Noise level	37 dB
Certification	UL, FCC Part15 Class B, CAN/CSA, ICES-003 Issue 6
Noise level (economic mode)	29 dB
Full HD	No
Supported video modes	480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Analog signal format system	Not supported
Supported graphics resolutions	640 x 480 (VGA), 800 x 600 (SVGA), 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA)
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN data rates	10, 100 Mbit/s
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Remote control type	IR