NEC MC453X User Manual

49
5. Using On-Screen Menu
...
Expand
Language
Auto setup
Keystone
Security
Power management
Test pattern
Network setup
Control ID
Factory default
Lamp counter reset
Filter
Expand
Security
OffPIN code lock
PIN code change
[Power management]
To reduce power consumption and maintain life cycle of light source, the power management function will turn off
the projection light source if your projector has no signals for a period of time.
1) Press ▲ ▼ button to select [Power management] menu.
2) Press <ENTER > button.
3) Press ▲ ▼ button to switch required item.
Ready......the power light indicator flashesgreen when the lamp is fully cooled down. The light source turns on
again if an input signal is connected or any key (except the power button ) on the side panel and remote controller
is pressed during this period of time.
Shut down......The projector shut down after the light source is fully cooled down.
Off......Disable the power management function.
Timer......Once the input signal is interrupted and no keys has been pressed for 30 seconds afterwards, the “No
signal” message displays in the timer. The timer counts down until the light source turns off. Press arrow key to set
up the timer in range of 1~30 minutes.
Ready countdown......Set the interval from ready mode change to standby mode (0 to 30 minutes) automatically.
When it is set it to zero, the projector will never change automatically. Press the Power key to change your projector
into standby mode and any other key to power on.
NOTE:
• Factory default for standby time: 5 minutes. Count down for ready mode: 5 minutes.
• When selecting [Off], the [Timer] and [Ready countdown] is unavailable.
• When selecting [Shut down], the [Timer] is unavailable.
...
Expand
Language
Auto setup
Keystone
Security
Power management
Test pattern
Network setup
Control ID
Factory default
Lamp counter reset
Filter
Expand
Power management
5 Min
5 Min
Ready
Off
Timer
Ready countdown
Shut down
Remaining time before
poweroff the light source.
01: 20
No signal

NEC MC453X Specifications

General

Native aspect ratio	4:3
Projection distance	0.9 - 10.9 m
Vertical scan range	50 - 120 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	16000:1
Screen size compatibility	30 - 300 \
Projector native resolution	XGA (1024x768)
Keystone correction, horizontal	-30 - 30 °
RMS rated power	16 W
Number of built-in speakers	1
Placement	Ceiling, Floor
Product type	Standard throw projector
Product color	White
Cable lock slot type	Kensington
Lamp power	240 W
Lamps quantity	1 lamp(s)
Light source type	Lamp
Lamp power (economic mode)	150 W
Service life of light source	10000 h
Service life of light source (economic mode)	20000 h
Built-in display	-
Focus	Manual
Throw ratio	1.5 - 1.8:1
Focal length range	19.158 - 23.018 mm
Aperture range (F-F)	1.6 - 1.76
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	320 W
Power consumption (standby)	0.5 W
Power consumption (typical)	305 W
Power consumption (economy mode)	215 W
Power consumption (network standby)	2 W
Noise level	37 dB
Certification	UL, FCC Part15 Class B, CAN/CSA, ICES-003 Issue 6
Noise level (economic mode)	29 dB
Full HD	No
Supported video modes	480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Analog signal format system	Not supported
Supported graphics resolutions	640 x 480 (VGA), 800 x 600 (SVGA), 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA)
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN data rates	10, 100 Mbit/s
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Remote control type	IR

Weight and Dimensions

Depth	261 mm
Width	345 mm
Height	108.4 mm
Weight	3300 g
Package depth	390 mm
Package width	450 mm
Package height	200 mm
Package weight	4700 g