nord NORDAC PRO SK 511E Series - Page 94

SK 54xE – Users Manual for Frequency Inverters
94 BU 0505 EN-3021
Operating displays
Abbreviations used:
• FI = Frequency inverter
• SW = Software version, stored in P707.
• S = Supervisor parameters are visible or hidden depending on P003.
Parameter
{factory setting}
Setting value / Description / Note Supervisor
Parameter
set
Pos: 123 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P000- P099/Parameter P000 – Betri ebsanzeige @ 0\mod_1327 573548773_388.doc x @ 7362 @ @ 1
P000
Operating display
(Operating parameter display)
0.01 ... 9999 In ParameterBoxes with 7-segment displays (e.g. SimpleBox) the operating value which is selected
in P001 is displayed online.
Important information about the operating status of the drive can be read out as required.
Pos: 124 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P000- P099/Parameter P001 – Aus wahl Anzeige @ 0\mod_132757372 8068_388.docx @ 7386 @ @ 1
P001
Display selection
(Display selection)
0 ... 65
{ 0 }
Selection of operating display of a parametrisation box with 7-segment display (e.g.: SimpleBox)
0 =
Actual frequency [Hz]
Currently supplied output frequency
1 =
Speed [rpm]
Calculated speed
2 =
Target frequency [Hz]
Output frequency that corresponds to the pending setpoint. This
need not correspond with the current output frequency.
3 =
Current [A]
Current measured output current
4 =
Actual torque current [A]:
Torque-forming output current
5 =
Voltage [V AC]
Current alternating voltage present at the device output
6 =
Link voltage [V DC]
The Link voltage [Vdc] is the FI-internal DC voltage. Amongst other
things, this depends on the level of the mains voltage.
7 =
cos Phi
Current calculated value of the power factor
8 =
Apparent power [kVA]
Calculated current apparent power
9 =
Effective power [kW]
Calculated current effective power
10 =
Torque [%]
Calculated current torque
11 =
Field [%]
Calculated current field in motor
12 =
Hours of operation [h]
Time for which main voltage present at device
13 =
Operating time Enable [h]
"Enabled operating hours"
is the time for which the device was
enabled.
14 =
Analogue input 1 [%]
Current value that is present at analogue input 1 of the device
15 =
Analogue input 2 [%]
Current value that is present at analogue input 2 of the device
16 =
… 18
Reserved, POSICON
19 =
Heat sink temperature [°C]
Current temperature of the heat sink
20 =
Actual utilisation of motor
[%]
Average motor utilisation, based on the known motor data
(P201...P209).
21 =
Brake resistor utilisation
[%]
"Braking resistor utilisation" is the average braking resistor load,
based on the known resistance data (P556...P557).
22 =
Interior temperature [°C]
Current interior temperature of device
(SK 54xE / SK 2xxE)
23 =
Motor temperature
Measured via KTY-84
24 =
… 29
Reserved
30 =
Present Target MP-S [Hz]
"Current motor potentiometer function setpoint with storage".
(P420…=71/72). The nominal value can be read out with this
function or pre-set (without the drive running).
31 =
… 39
Reserved
40 =
PLC control box value
Visualisation mode for PLC communication
41 =
… 59
Reserved, POSICON
60 =
R stator ident
Stator resistance determined by means of measurement (P220)