Oakton WP PCD 650 - MV Setup (no Settings Available)

120 pages

Save Page as PDF

To Next Page

To Previous Page

Instruction Manual PCD 650

4.4 mV setup (no settings available)

No settings are available for mV.

Figure 76: mV Setting Page

Press ESC (F4) to go to measurement mode.

Main Page

Table of Contents5
Getting Started9
About the Meter9
Display & Keypad10
Display Overview10
Key Functions11
Inserting Batteries12
Inserting Batteries for the First Time12
Changing Batteries Subsequently13
Connecting DC Power Adapter13
Attaching Safety Belt14
Connecting Peripherals15
Probes (Ph/Conductivity/Do)15
Protective Rubber Boot16
Multi Probe Holder16
Cybercomm 600 Data Acquisition Software18
About Cybercomm 600 das Application18
Installing Cybercomm 60018
Starting Cybercomm 600 for the First Time18
Connecting to the Meter20
Measurement Mode23
About Measurement Mode23
Accessing Functions23
Taking Measurement25
Prepare the Meter for Measurement25
Taking a Reading25
Stable Reading Indicator25
Holding a Reading25
Automatic Temperature Compensation (ATC)26
Manual Temperature Compensation (MTC)26
Alarm Set Point (for Ph/Conductivity/Do)26
Calibration Due (CAL-DUE) Indicator (for Ph/Conductivity/Do)26
Resolution of Ph Reading26
Ph Buffer Group for Calibration and Auto-Recognition26
Ph Calibration Points27
Conductivity Calibration Mode27
Conductivity Calibration Points27
Cell Constant27
Normalization Temperature ( ° C)27
Linear Temperature Coefficient28
Pure Water Coefficient28
Set Salinity28
Auto Salinity Compensation28
Saturation Offset Adjustment28
Set Barometer Pressure Range and Barometric Pressure Units28
Pressure Compensation28
Multi Display Mode30
Ph Measurement Mode31
Indicators in Ph Measurement Screen31
MV Measurement Mode32
Indicators in MV Measurement Mode32
Ion Measurement Mode33
Changing Unit of Measurement33
Indicators in Ion Measurement Mode33
Conductivity Measurement Mode34
Indicators in Conductivity Measurement Screen34
Refer Item Numbers Indicated in Figure 2534
TDS Measurement Mode35
Indicators in TDS Measurement Mode35
Salinity Measurement Mode36
Indicators in Salinity Measurement Mode36
Resistivity Measurement Mode37
Indicators in Resistivity Measurement Mode37
Percentage Saturation (%) Measurement Mode38
Indicators in Percentage Saturation Measurement Mode38
Measurement Mode Indicator38
Appears When the Reading Is Stable38
Appears When the Reading Is on Hold38
Ion Reading38
Units of Measurement38
Concentration (Mg/L) (Ppm) Measurement Mode39
Indicators in Concentration Measurement Screen39
Transfer Measured Data to Computer (Cybercomm)40
Sending a Single Reading from Multi Measurement Mode40
Sending a Single Reading from Single Measurement Mode41
Sending Readings Continuously in Single and Multi Measurement Modes42
Saving Data43
Working with Memory Functions44
Logging Data Automatically in Meter's Memory44
Storing Currently Displayed Reading in the Memory (in Irda and LED Print Mode)44
Viewing Stored Data44
Transferring Stored Data to Computer (Cybercomm) through Irda45
Calibration Mode47
About Calibration47
About Temperature Calibration47
About Ph Calibration47
About Ion Calibration48
About Conductivity/Resistivity/Tds/Salinity Calibration48
About DO(%) and DO (Mg/L) Calibration48
Prepare the Meter for Calibration49
Accessing Calibration Mode50
Accessing Calibration Mode When Password Protection Enabled50
Temperature Calibration52
Temperature Calibration for ATC Mode52
Temperature Calibration for MTC Mode53
Ph Calibration54
Ph Calibration with a Standard Buffer54
Ph Calibration with a User-Defined Buffer55
Calibration Report56
Average Slope Indicator of Ph Probe57
MV Calibration59
MV Reading59
MV Calibration Report60
Ion Calibration61
Calibration Report62
Conductivity Calibration63
Manual Calibration63
Automatic Calibration (for Conductivity Calibration)64
Calibration Report66
Resistivity Calibration67
Resistivity Calibration Report68
Salinity Calibration69
Salinity Calibration Report70
TDS Calibration71
TDS Calibration Report72
DO Calibration in % Saturation Mode (with ATC)73
To Calibrate 100% Saturation73
To Calibrate 0% Saturation75
DO Calibration Report75
DO Calibration in Mg/L or Ppm Concentration Mode77
Concentration Calibration Report78
Setup Mode79
About Setup Mode79
Accessing Setup Mode (no Password Protection Enabled)79
Accessing Setup Mode When Password Protection Enabled81
Modifying Setup Parameters82
System Setup83
System Settings83
System Settings85
System Settings86
System Settings87
System Settings88
System Settings89
Ph Setup90
Ph Settings90
Ph Settings91
MV Setup (no Settings Available)92
Ion Setup93
Ion Settings Page93
Conductivity Setup94
Conductivity Settings94
Conductivity Settings95
TDS Setup96
TDS Settings96
TDS Settings97
Salinity Setup98
Salinity Settings98
Salinity Settings – Page 298
Resistivity Setup100
Resistivity Settings100
Resistivity Settings – Page 2100
DO Saturation Setup102
Do (%)102
DO (%) – Page 1102
Do (%)103
DO (%) – Page 2103
O 2 Mg/L (Ppm) - DO Concentration Setup104
DO (Mg/L)104
DO (Mg/L)105
Temperature Setup106
Temperature Setting Page106
Technical Specifications107
Accessories110
Replacement Accessories110
Optional Accessories110
Oakton Instruments111
Appendix112
Conductivity Theory112
Calculating TDS Conversion Factor114
Calculating Temperature Coefficients114
Dissolved Oxygen Probe115
Dissolved Oxygen Principle115
Probe Care115
Membrane Housing Replacement116
Membrane/O-Ring Replacement (Optional Procedure)116
Electrolyte Solution117
General Information118
Warranty118

Oakton WP PCD 650 - MV Setup (no Settings Available)

Table of Contents

Related product manuals