Why is the wrong user ID displayed on my Omron Personal Care Product?
If your Omron Personal Care Product shows an incorrect user ID when you step on it, it could be due to a few reasons: * Your body weight has changed significantly since your last measurement; in this case, select your user ID before taking a measurement. * Your body type is similar to another set-up person. * The measurement results of another user has been set-up.
Why is my Omron Personal Care Product not turning on?
If your Omron Personal Care Product monitor displays nothing even when you step on it or turn it on, there might be a few reasons: * Check if the batteries are inserted. * Ensure the batteries are inserted in the correct direction. * The batteries may be worn out, so try replacing all four with new ones.
What does ' ' mean on my Omron Personal Care Product?
If your Omron Personal Care Product displays ' ' for some results, it indicates that the set-up data or body composition values were outside the measurable range. Verify that the birth date, gender, and height settings are correct. Note that even with correct settings, this symbol may appear if the values are outside the supported age range.
Why is my Omron Personal Care Product giving inaccurate readings?
If your Omron Personal Care Product measurement result is higher or lower than expected, or varies widely, consider the following: * Ensure you maintain correct posture during measurement. * Place the monitor on a hard, level floor, not carpet or an uneven surface. * Warm your body to improve blood circulation if you or the soles of your feet are cold. * Allow cold foot electrodes to warm up by leaving the monitor in a warm room. * Slightly moisten the soles of your feet if they are dry. * Implement the “0 lb correction” correctly.
What to do if batteries are depleted in Omron Personal Care Product?
If the batteries of your Omron Personal Care Product are depleted, replace them. It is recommended to replace the batteries with new ones ahead of time.
What to do if batteries are low in Omron Personal Care Product?
If the batteries of your Omron Personal Care Product are low, it is recommended to replace them with new ones ahead of time.
Why is my Omron Personal Care Product only showing weight?
If you're trying to measure body composition with your Omron Personal Care Product, but only body weight is displayed, make sure you select your User ID or GUEST before taking the measurement.
What to do if Omron Personal Care Product button doesn't respond?
If your Omron Personal Care Product button doesn't respond, it might be due to these reasons: * You pressed a button while standing on the monitor; step off before pressing any buttons. * The button is wet; wipe off any water or stains. * You pressed multiple buttons at once; press one at a time.
What does communication failure mean on Omron Personal Care Product?
If your Omron Personal Care Product shows a 'Communication failure', turn off the power and attempt to communicate again. If the error persists, contact customer service.
What does device error mean on Omron Personal Care Product?
If your Omron Personal Care Product displays 'Device error', remove and re-insert the battery. Restart the monitor. If the error continues, contact customer service.
General| Brand | Omron |
|---|---|
| Model | BCM-500 |
| Category | Personal Care Products |
| Language | English |
Covers the manual's introduction, intended use, and initial device inspection.
Details essential safety instructions, warnings, and contraindications for monitor use.
Overview of the body composition monitor and scale, including its components and display.
Instructions for installing and replacing the AAA batteries in the monitor.
Steps to connect the OMRON BCM-500 monitor with a compatible smart device via Bluetooth.
Guide to setting the measurement units, date, and time on the body composition monitor.
Process for entering personal information such as birth date, gender, and height for accurate measurements.
Provides guidance on proper posture and conditions for accurate body composition measurements.
Step-by-step instructions on how to perform a body composition measurement using the monitor.
Instructions on how to access and view measurement results via the OMRON HeartAdvisor app.
Procedure for manually selecting a user ID when automatic recognition fails.
How to use the monitor for measurements that are not saved to a user profile.
Instructions for using the monitor to measure body weight only, without body composition.
Steps to modify or remove personal data stored on the body composition monitor.
Guide to removing the Bluetooth communication settings from the monitor.
Guidelines for cleaning, storing, and maintaining the body composition monitor.
Common error displays and their causes and solutions for the body composition monitor.
Technical details and specifications of the OMRON BCM-500 Body Composition Monitor.
Information regarding FCC compliance and radio frequency regulations for the device.
Details of the product warranty, terms, and conditions for the OMRON monitor.
Information on EMC compliance and manufacturer's declarations for the device.
Explanation of the principle of body composition calculation and recommended measurement times.
Diagrams and tables to help understand and interpret body fat and visceral fat level results.
To Next Page
