Oriental motor BLE Series - 13 Accessories (Sold Separately); Connection Cables and Regeneration Unit; Speed Indicator, Data Setter, and Software Cable; DIN Rail Mounting Plate

Accessories (sold separately)
−
51
−
13 Accessories (sold separately)

Connection cable
This cable is used to extend the wiring distance between the driver and motor. Connection can be extended to a maximum
of 20.4 m (66.9 ft.). Flexible connection cables are also available. You can connect up to three connection cables.
•
Standard type
Connection cable
•
Standard type
Flexible connection cable
•
Electromagnetic brake type
Connection cable
•
Electromagnetic brake type
Flexible connection cable
Length
[m (ft.)]
Model
Length
[m (ft.)]
Model
Length
[m (ft.)]
Model
Length
[m (ft.)]
Model
1 (3.3)
CC01BLE
1 (3.3)
CC01BLER
1 (3.3)
CC01BLEM
1 (3.3)
CC01BLEMR
2 (6.6)
CC02BLE
2 (6.6)
CC02BLER
2 (6.6)
CC02BLEM
2 (6.6)
CC02BLEMR
3 (9.8)
CC03BLE
3 (9.8)
CC03BLER
3 (9.8)
CC03BLEM
3 (9.8)
CC03BLEMR
5 (16.4)
CC05BLE
5 (16.4)
CC05BLER
5 (16.4)
CC05BLEM
5 (16.4)
CC05BLEMR
7 (23.0)
CC07BLE
7 (23.0)
CC07BLER
7 (23.0)
CC07BLEM
7 (23.0)
CC07BLEMR
10 (32.8)
CC10BLE
10 (32.8)
CC10BLER
10 (32.8)
CC10BLEM
10 (32.8)
CC10BLEMR
15 (49.2)
CC15BLE
15 (49.2)
CC15BLER
15 (49.2)
CC15BLEM
15 (49.2)
CC15BLEMR
20 (65.6)
CC20BLE
20 (65.6)
CC20BLER
20 (65.6)
CC20BLEM
20 (65.6)
CC20BLEMR

Regeneration unit
Connect the regeneration unit if gravitational operation or sudden starting/stopping of a large inertial load, will be
repeated frequently.
Model:
EPRC-400P

Digital speed indicator
This device displays the speed of the motor output shaft and reduced speed of the gearhead output shaft.
Model:
SDM496
Note
•
The
SDM496
is not certied under safety standards. If the
SDM496
is combined with a
BLE
Series unit, the
BLE
Series unit does not conform to safety standards, either.
•
The
SDM496
cannot be used with the source logic.
7
5
6
SDM496 Driver
2
10
9
FG FG
SPEED signal input SPEED-OUT (+)
SPEED-OUT (
- )GND
Power supply input
Single-phase100-240 V
50/60 Hz
7
5
6
SDM496 Driver
2
10
9
SPEED signal input SPEED-OUT (+)
SPEED-OUT (
- )GND
Not connected.
• Basic connection (30 pulses/revolution)
• FBLⅡcompatible mode (12 pulses/revolution)
Selection of 12 pulses or
30 pulses
Selection of 12 pulses or
30 pulses
Power supply input
Single-phase 100-240 V
50/60 Hz

Data setter
This data setter can be used to set or monitor operation data and parameters.
Model:
OPX-2A

Communication cable for the support software
Be sure to purchase the communication cable for the support software when connecting a driver and PC in which the
support software
MEXE02
has been installed.
This is a set of a PC interface cable and USB cable. The cable is connected to the USB port on the PC.
Model:
CC05IF-USB
[5 m (16.4 ft.)]
The
MEXE02
can be downloaded from Oriental Motor Website Download Page. Also, the
MEXE02
is provided in
the form of a storage medium. For details, check out our web site or contact your nearest Oriental Motor sales ofce.

DIN rail mounting plate
When mounting the driver to a DIN rail, use a DIN rail mounting plate. Use a DIN rail 35 mm (1.38 in.) wide.
Model:
PADP03