Oriental motor BLVD20KM - Input signals list; Output signals list

Setting contents of MEXE02
−59−

Input signals list
Signal name Description
Not used Set when the input signal is not used.
FWD
When setting to
2-wire mode
When this signal is turned ON, the motor rotates in the clockwise direction.
The rotation direction can be changed using the "Motor rotation direction
selection" parameter.
REV
When this signal is turned ON, the motor rotates in the counterclockwise
direction.
The rotation direction can be changed using the "Motor rotation direction
selection" parameter.
STOP-MODE
Select how to stop the motor.
The motor decelerates to a stop when this signal is turned ON, and it stops
instantaneously when turned OFF.
START/STOP
When setting to
3-wire mode
When this signal is turned ON, the motor rotates. The motor decelerates to a
stop when it is turned OFF.
RUN/BRAKE
When this signal is turned ON, the motor rotates. The motor stops
instantaneously when turned OFF.
FWD/REV
This signal is used to change the motor rotation direction.
The motor rotates in the counterclockwise direction when the signal is turned
ON, and it rotates in the clockwise direction when turned OFF.
The rotation direction can be changed using the "Motor rotation direction
selection" parameter.
MB-FREE
This signal is used to select how the electromagnetic brake would operate when the motor stops. If
this signal is turned ON, the electromagnetic brake is released.
EXT-ERROR If this signal is turned OFF, the external stop alarm is generated to stop the motor.
ALARM-RESET This signal is used to reset the alarm.
HMI
When the HMI input is turned ON, the function limitation of the MEXE02 and OPX-2A is released.
When the HMI input is turned OFF, the function limitation is imposed.
[ Functions to be limited ]
•∗
Writing operation data and parameters
•∗
I/O test
•∗
Teaching, remote operation
•∗
Clearing of history and others
•∗
Conguration
•∗
Initialization (Restores to factory settings)
M0 to M2 Select the set operation data by a combination of ON-OFF status of M0, M1 and M2 inputs.

Output signals list
Signal name Description
Not used Set when the output terminal is not used.
FWD_R
When setting to
2-wire mode
Output in response to the FWD input.
REV_R Output in response to the REV input.
STOP-MODE_R Output in response to the STOP-MODE input.
START/STOP_R
When setting to
3-wire mode
Output in response to the START/STOP input.
RUN/BRAKE_R Output in response to the RUN/BRAKE input.
FWD/REV_R Output in response to the FWD/REV input.
MB-FREE_R Output in response to the MB-FREE input.
M0_R to M2_R Output in response to the M0 to M2.
ALARM-OUT1 This signal is output when an alarm is generated.
WNG This signal is output when a warning is generated.
MOVE Output while the motor operates.
TLC This signal is output when the motor output torque reaches the value set in the torque limiting value.
VA
This signal is output when the speed dierence between the set rotation speed and actual motor rotation
speed becomes equal to or less than the value set with the "Rotation speed attainment band" parameter.
S-BSY
This signal is turned ON at the following conditions.
•
When the maintenance command is being executed via RS-485 communication.
•
When Conguration, teaching/remote operation, or I/O test is being executed with the
MEXE02
.
•
When operation data or a parameter is being written with the
MEXE02
or the
OPX-2A
.
While this signal is being ON, operation data cannot be rewritten or the maintenance command cannot be
executed.
ALARM-OUT2 This signal is output when a load applied to the motor exceeds the overload warning level.
MPS The MPS output is turned ON when the main power supply is turned on.
DIR
Output a state of the rotation direction of the motor shaft.
The rotation direction represents the forward direction if this signal is ON, and the reverse direction if this
signal is OFF.