Oriental motor US2D6-JA User Manual

Safety precautions
−
4
−
1 Safety precautions
The precautions described below are intended to prevent danger or injury to the user and other personnel through safe,
correct use of the product. Use the product only after carefully reading and fully understanding these instructions.
Description of graphic symbols
Indicates "prohibited" actions that must
not be performed.
Indicates "compulsory" actions that must be
performed.
Warning
Handling the product without observing the instructions that accompany a “Warning” symbol may result in
serious injury or death.
•
Do not use the product in explosive or corrosive
environments, in the presence of ammable gases, locations
subjected to splashing water, or near combustibles. Doing
so may result in re, electric shock, or injury.
•
Do not transport, install, connect or inspect the product
while the power is supplied. Always turn the power off
before carrying out these operations. Failure to do so may
result in electric shock.
•
The terminals on the speed controller front panel marked
with
symbol indicate the presence of high
voltage. Do not touch the CN1 and CN2 while the power
is ON. Doing so may result in re or electric shock.
•
Do not forcibly bend, pull or pinch the cable. Doing so
may cause re or electric shock.
•
Do not touch the connector of the speed controller
immediately after the power is turned off (for a period of
1 minute). The residual voltage may cause electric shock.
•
Do not disassemble or modify the motor and speed
controller. This may cause electric shock or injury.
•
Only qualied and educated personnel should be allowed
to perform installation, connection, operation and
inspection/troubleshooting of the product.
Handling by unqualied and uneducated personnel may
result in re, electric shock, or injury.
•
The motor is Class I equipment.
When installing the motor, ground the Protective Earth
Terminal of the motor. Failure to do so may result in
electric shock.
•
Install the motor and speed controller in an enclosure.
Failure to do so may result in electric shock or injury.
•
Observe the rated range for the the AC power supply voltage
to input to the speed controller. Failure to do so may result in
re or damage to equipment.
•
Securely connect and ground in accordance with the section
for connection. Failure to do so may result in re or electric
shock.
•
Be sure to observe the specied cable sizes. Use of
unspecied cable sizes may result in re.
Caution
Handling the product without observing the instructions that accompany a “Caution” symbol may result in
injury or property damage.
•
Do not use the motor and speed controller beyond their
specications. Doing so may result in electric shock,
injury or damage to equipment.
•
Do not carry the motor by holding the motor output shaft or
motor cable. Doing so may result in injury.
•
Keep the area around the motor and speed controller free
of combustible materials. Failure to do so may result in
re or a skin burn(s).
•
Do not leave anything around the motor and speed
controller that would obstruct ventilation. Doing so may
result in damage to equipment.
•
Do not wire the electromagnetic contactor or power relay
between the motor and speed controller. To switch the
rotation direction using the electromagnetic contactor may
cause damage to equipment.
•
Do not touch the rotating part (output shaft) while
operating the motor. Doing so may result in injury.
•
If an alarm of the speed controller is generated, rst
remove the cause and then reset the alarm. Failure to do
so may result in injury or damage to equipment.
•
Do not use the product in elevating applications (vertical
drives). Doing so may result in injury or damage to
equipment.
•
Securely install the motor and speed controller to their
respective mounting plates. Inappropriate installation may
cause the motor and speed controller to detach and fall,
resulting in injury or equipment damage.
•
Use a motor and speed controller only in the specied
combination. An incorrect combination may cause a re.
•
Provide an emergency stop device or emergency stop
circuit external to the equipment so that the entire
equipment will operate safely in the event of a system
failure or malfunction. Failure to do so may result in injury.
•
Be sure to ground the motor and speed controller to
prevent them from being damaged by static electricity.
Failure to do so may result in damage to equipment.
•
Immediately when trouble has occurred, stop running and
turn off the speed controller power. Failure to do so may
result in re, electrical shock or injury.
•
The motor surface temperature may
exceed 70 °C (158 °F) even under normal
operating conditions. If the operator is
allowed to approach a running motor,
attach a warning label as shown in the
gure in a conspicuous position. Failure
to do so may result in skin burn(s).
Warning label
•
Conduct the insulation resistance measurement or
dielectric strength test separately on the motor and
speed controller. Conducting while the motor and
speed controller are connected may result in damage to
equipment.
•
To dispose of the motor and speed controller, disassemble
it into parts and components as much as possible and
dispose of individual parts/components as industrial
waste.

Oriental motor US2D6-JA Specifications

General

Brand	Oriental motor
Model	US2D6-JA
Category	Engine
Language	English