Orion OPM-4260 - MSCS Protocol Commands (Time & Status); Time, Serial Number, and Status Commands

- 74 - - 75 -
- Receive from MPDP
STX CMD Length
Data
Check Sum ETX
ID Master
Value 0x02 Variable 0x02 Variable 0X01 Variable 0x03
* ID range (Program): 0x01(1) ~ 0xFF(255)
* Check Sum: execute "Not" operation after adding all the values in "STX~Data" area.
3.12. Elapsed Time
- Command for informing the elapsed time of each PDP set. (Basic unit: hour)
- It is available only on Power On (Operative) status.
- CMD : 0x77 (Get), 0x7B (Initial)
- Send to MPDP
STX CMD Length
Data
ETX
ID Master
Value 0x02 Variable 0x02 Variable 0X01 0x03
* ID range (Program): 0x01(1) ~ 0xFF(255)
* It is not applicable as "Broad-cast" command
- Receive from MPDP
STX CMD Length
Data
Check
Sum
ETX
ID Master Elapsed Time
Value 0x02 Variable 0x08 Variable 0X01 … Variable 0x03
Hundred
thousands
ten thou-
sands
thousands hundreds ten one
Variable Variable Variable Variable Variable Variable
* ID range(Program): 0x01(1) ~ 0xFF(255)
* Check Sum: Execute "Not" operation after adding all the values in "STX~Data" area.
* Elapsed Time
- Hundred thousands, ten thousands, thousands, hundreds, tens, ones: 0(0x00)~9(0x09) range value.
3.13. IP Serial Number
- Command for assigning and identifying the serial numbers of each IP board. (8 digit)
CMD: 0x75 (Get S/N), 0x76 (Set S/N)
- Send to MPDP
STX CMD Length
Data
ETX
ID Master
Value 0x02 Variable 0x02 Variable 0X01 0x03
* ID range (Program): 0x01(1) ~ 0xFF(255)
* "Get/Set IP Serial Number"(0x75/0x76) command is not applicable as "Broad-cast" command, because each PDP should have an
unique serial number.
- Receive from MPDP
STX CMD Length
Data
Check
Sum
ETX
ID Master S/N
Value 0x02 Variable 0x0A Variable 0x01 … Variable 0x03
0 1st 2nd 3rd 4th 5th 6th 7th
Variable Variable Variable Variable Variable Variable Variable Variable
* ID range(Program): 0x01(1) ~ 0xFF(255)
* Check Sum: Execute "Not" operation after adding all the values in "STX~Data" area.
* Elapsed Time
- 0, 1st, 2nd, 3rd, 4th, 5th, 6th, 7th: 0(0x00)~9(0x09) range value
3.14. Get Current Status
- Command for obtain the current PDP (IP) information
- CMD: 0x87
- It is available only on Power On (Operative) status.
- Send to MPDP
STX CMD Length
Data
ETX
ID Master
Value 0x02 0x87 0x02 Variable 0X01 0x03
* ID range (Program): 0x01(1) ~ 0xFF(255)
* It cannot be used as "Broad-cast" command.
- Receive from MPDP
STX CMD Length
Data
Check Sum ETX
ID Master Status
Value 0x02 0x87 0x23 Variable 0X01 … Variable 0x03
* ID range(Program): 0x01(1) ~ 0xFF(255)
* Check Sum: Execute "Not" operation after adding all the values in "STX~Data" area.
* Status (32 byte)
No. Data Length Explanation
1 PWR Status 1 byte 0: Power Off (Stand-by), 1: Power On (Working)
2 Input Source 1 byte 0x0C: PC, 0x0E: DVI, 0x0D: DTV, 0x07: DVD, 0x05: S-Video, 0x02: Video
3 Resolution 1 byte The value of "Displayed Resolution at the time of detection"
4 Not Used
5 Global Offset 1 byte 0: Global Offset Off, 1: Global Offset On
6 Color Temp. 1 byte 0: Normal mode, 1: Studio mode
7 Auto-Power Mode 1 byte 0: Auto-Power Off, 1: Auto-Power On
8 FAN Mode 1 byte 0 : Auto, 1: Full
9 Temperature0 1 byte
0(0x00): 0˚C~ 127(0x7F): 127˚C / 128(0x80): -1˚C ~ 254(0xFE): -127˚C
0xFF: Temp. Sensor Error
10 Temperature1 1 byte
0(0x00): 0˚C ~ 127(0x7F): 127˚C / 128(0x80): -1˚C ~ 254(0xFE): -127˚C
0xFF: Temp. Sensor Error
11 FAN Status 1 byte 0x30: Good, 0x31: Error
12~18 F/W Version 7 byte
Year: 2 byte, Month: 2byte, Day: 2byte, Rev.(0~9):1byte
Ex) December 29th, 2012 Rev. 2 → 0x01 0x02 0x01 0x02 0x02 0x09 0x02
19 Not Used
20~27 S/N 8 byte
123456 → 0x00 0x00 0x01 0x02 0x03 0x04 0x05 0x06
1 → 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x01
OPM-4260 | OPM-4260R
Innitely Expandable