Orion OPM-4260 - MSCS Protocol Commands (Data & Calibration); Picture Data and Auto Calibration Commands

- 82 - - 83 -
3.21. Get Picture Control Data
- Command for acquiring the current Picture Control Data(User Mode, White Balance, Graphic, Video)
- CMD: 0x88
- It is available only on Power On (Operative) status.
- The values based on current Color Temp. (Normal Mode / Studio Mode) will be displayed.
- Send to MPDP
STX CMD Length
Data
ETX
ID Master
Value 0x02 0x88 0x02 Variable 0x01 0x03
* ID range(Program): 0x01(1) ~ 0xFF(255)
* It is not applicable as "Broad-cast" command.
- Receive from MPDP
STX CMD Length
Data
Check Sum ETX
ID Master Control
Value 0x02 0x88 0x34 Variable 0x01 … Variable 0x03
* ID range(Program): 0x01(1) ~ 0xFF(255)
* Control (50 byte)
No. Data Length Explanation
1 User Mode – Brightness 1 byte Range: 0(0x00) ~ 100(0x64)
2 User Mode – Contrast 1 byte Range: 0(0x00) ~ 100(0x64)
3 User Mode – Sharpness 1 byte Range: 0(0x00) ~ 28(0x1C)
4 Not Used
5 Not Used
6 White Balance – Gain R 1 byte Range: 0(0x00) ~ 255(0xFF)
7 White Balance – Gain G 1 byte Range: 0(0x00) ~ 255(0xFF)
8 White Balance – Gain B 1 byte Range: 0(0x00) ~ 255(0xFF)
9 White Balance – Offset R 1 byte Range: 0(0x00) ~ 255(0xFF)
10 White Balance – Offset G 1 byte Range: 0(0x00) ~ 255(0xFF)
11 White Balance – Offset B 1 byte Range: 0(0x00) ~ 255(0xFF)
12, 13 RGB - Gain R 2byte Range : 0(0x000) ~ 1023(0X3FF)
14, 15 RGB - Gain G 2byte Range : 0(0x000) ~ 1023(0X3FF)
16, 17 RGB - Gain B 2byte Range : 0(0x000) ~ 1023(0X3FF)
18, 19 RGB - Offset R 2byte Range : 0(0x000) ~ 1023(0X3FF)
20, 21 RGB - Offset G 2byte Range : 0(0x000) ~ 1023(0X3FF)
22, 23 RGB - Offset B 2byte Range : 0(0x000) ~ 1023(0X3FF)
24 ~ 47 Not Used 24btye
48 Video Brightness 1byte Range : 0(0x00) ~ 255(0xFF)
49 Video Contrast 1byte Range : 0(0x00) ~ 255(0xFF)
50 Video Color 1byte Range : 0(0x00) ~ 255(0xFF)
3.22. Auto Calibration
- Command for synchronizing the ADC Gain and Offset for 16-Gray input. It is available only for PC.
- It is available only on Power On (Operative) status.
- CMD : 0x80
- Send to MPDP
A. Normal Command
STX CMD Length
Data
ETX
ID Master
Value 0x02 0x80 0x02 Variable 0x01 0x03
B. Broadcast Command
STX CMD Length Data: ID ETX
Value 0x02 0x80 0x01 0x00 0x03
* ID range (Program): 0x01(1) ~ 0xFF(255)
* Broadcast: All PDP sets will execute the same command, when the ID is 0x00. No response (One way command)
- Receive From MPDP
STX CMD Length
Data
Check Sum ETX
ID Master
Value 0x02 0x80 0x02 Variable 0x01 Variable 0x03
3.23. Factory Data (Picture Control Data)
- Command for loading the Picure Control data (User Mode / White Balance / RGB Data / VIDEO Data) adjusted
in the factory.
- CMD : 0x82(Save), 0x83(Load))
- It is usable only at Power on Operative
- It shows the value based on current Color Temp. (Normal Mode / Studio Mode.)
- Data can be checked with "Get Picture Control Data" after executing the command
- Send to MPDP
STX CMD Length
Data
ETX
ID Master
Value 0x02 Variable 0x02 Variable 0x01 0x03
* ID range(Program): 0x01(1) ~ 0xFF(255)
- Receive from MPDP
STX CMD Length
Data
Check Sum ETX
ID Master
Value 0x02 Variable 0x02 Variable 0x01 Variable 0x03
* ID range(Program): 0x01(1) ~ 0xFF(255)
* Check Sum: Execute "Not" operation after adding all the values in "STX~Data" area.
OPM-4260 | OPM-4260R
Innitely Expandable