Panasonic AG-CX350

– 136 –
Chapter 5 Shooting — Audio input
Audio input
The camera can record four channels of audio.
(However, two channels when AVCHD is selected as the recording le format)
The audio to input to each channel can be switched to the built-in microphone, an external microphone, or a connected audio device.
Switching the audio input
r Audio recording format
The audio recording format such as compression format varies depending on the recording mode.
Recording mode Recording format Sampling rate/bit
P2 Linear PCM (LPCM) 48 kHz/24 bit*
MOV Linear PCM (LPCM) 48 kHz/24 bit
AVCHD Dolby Audio
TM
48 kHz/16 bit
* When the [REC FORMAT] is set to following, it will be 48 kHz/16 bit.
[1080-59.94p/AVC-G12]
[1080-50.00p/AVC-G12]
[1080-59.94i/AVC-G12]
[1080-50.00i/AVC-G12]
[720-59.94p/AVC-G12]
[720-50.00p/AVC-G12]
When the [REC FORMAT] is set to following, 48 kHz/16 bits or 48 kHz/24 bits can be selected in the [SYSTEM] menu → [AUDIO SAMPLE RES.].
[1080-50.00i/AVC-I100]
[1080-50.00p/AVC-I100]
[1080-59.94i/AVC-I100]
[1080-59.94p/AVC-I100]
[720-50.00p/AVC-I100]
[720-59.94p/AVC-I100]
[1080-50.00i/AVC-I50]
[1080-59.94i/AVC-I50]
[720-50.00p/AVC-I50]
[720-59.94p/AVC-I50]
r Selecting audio input signals
Selects the audio signal to record in the audio channel 1/audio channel 2.
Audio signal to record in the audio channel 3/audio channel 4 is automatically set with the settings of the <CH1 SELECT> switch and the <CH2
SELECT> switch.
Item Input signal to be recorded
<CH1 SELECT> <CH2 SELECT> Audio channel 1 Audio channel 2 Audio channel 3 Audio channel 4
<INT(L)> <INT(R)> Built-in microphone <L> Built-in microphone <R> <AUDIO INPUT 1>
terminal
<AUDIO INPUT 2>
terminal
<INPUT1> Built-in microphone <L> <AUDIO INPUT 1>
terminal
<AUDIO INPUT 1>
terminal
Built-in microphone <R>
<INPUT2> Built-in microphone <L> <AUDIO INPUT 2>
terminal
<AUDIO INPUT 1>
terminal
Built-in microphone <R>
<INPUT1> <INT(R)> <AUDIO INPUT 1>
terminal
Built-in microphone <R> Built-in microphone <L> <AUDIO INPUT 2>
terminal
<INPUT1> <AUDIO INPUT 1>
terminal
<AUDIO INPUT 1>
terminal
Built-in microphone <L> Built-in microphone <R>
<INPUT2> <AUDIO INPUT 1>
terminal
<AUDIO INPUT 2>
terminal
Built-in microphone <L> Built-in microphone <R>
<INPUT2> <INT(R)> <AUDIO INPUT 2>
terminal
Built-in microphone <R> Built-in microphone <L> <AUDIO INPUT 2>
terminal
<INPUT1> <AUDIO INPUT 2>
terminal
<AUDIO INPUT 1>
terminal
Built-in microphone <L> Built-in microphone <R>
<INPUT2> <AUDIO INPUT 2>
terminal
<AUDIO INPUT 2>
terminal
Built-in microphone <L> Built-in microphone <R>
When using the built-in microphone
1
Set the <CH1 SELECT> switch to the <INT(L)> position.
The audio signal of the built-in microphone <L> is recorded in the audio channel 1.
2
Set the <CH2 SELECT> switch to the <INT(R)> position.
The audio signal of the built-in microphone <R> is recorded in the audio channel 2.
@@
NOTE
t To decrease the wind noise of the microphone, select the [AUDIO] menu → [REC CH SETTINGS] → [CH1 MIC LOWCUT]/[CH2 MIC LOWCUT]/[CH3
MIC LOWCUT]/[CH4 MIC LOWCUT] → [ON].