Panasonic AJ-PX800G - Page 125

– 125 –
Chapter 6 Menu Operations — Menu list
Item Description of settings
[Yl-R-R (PHASE)] Corrects the hue between “colors between yellow and red” and red.
[−63]…[63]
f Factory setting: [0]
[MASTER PED] Sets the master pedestal.
[−200]…[200]
f Factory setting: [16]
[RGB BLACK CONTROL
SETTING]
[R PED] Sets the Rch pedestal level.
[−100]…[100]
f Factory setting: [0]
[G PED] Sets the Gch pedestal level.
[−100]…[100]
f Factory setting: [0]
[B PED] Sets the Bch pedestal level.
[−100]…[100]
f Factory setting: [0]
[PEDESTAL OFFSET] Sets the Rch, Gch, and Bch pedestal levels after adjusting the automatic black balance.
[ON]: Keeps each of the values set in [R PED], [G PED], and [B PED].
[OFF]: Sets the pedestal level of Rch, Gch, and Bch to [0].
f Factory setting: [OFF]
[GAMMA MODE SEL] Selects the gamma curve.
[HD]: The video gamma feature for HD (High Denition).
[SD]: Increases gain in darker areas more than HD gamma.
[FILMLIKE1]: Feature that reproduces more highlight areas compared to HD gamma.
[FILMLIKE2]: Feature that reproduces more highlight areas compared to [FILMLIKE1].
[FILMLIKE3]: Feature that reproduces more highlight areas compared to [FILMLIKE2].
[FILM-REC]: The cine gamma feature for lm.
[VIDEO-REC]: The cine gamma feature for video.
f Factory setting: [HD]
[GAMMA SETTING] [MASTER GAMMA] Sets the master gamma in 0.01 steps.
[0.30]…[0.75]
f Factory setting: [0.45]
[F-REC DYNAMIC LVL] When [FILM-REC] is selected in [GAMMA MODE SEL], dynamic range is set. If an item other than
[FILM-REC] is selected, no settings are changed.
[200%], [300%], [400%], [500%], [600%]
f Factory setting: [600%]
[F-REC BLACK STR
LVL]
When [FILM-REC] is selected in [GAMMA MODE SEL], black stretch is set. If an item other than
[FILM-REC] is selected, no settings are changed.
[0%]…[30%]
f Factory setting: [0%]
[V-REC KNEE SLOPE] When [VIDEO-REC] is selected in [GAMMA MODE SEL], knee slope is set. If an item other than
[VIDEO-REC] is selected, no settings are changed.
[150%], [200%]…[500%]
f Factory setting: [500%]
[V-REC KNEE POINT] When [VIDEO-REC] is selected in [GAMMA MODE SEL], knee point is set. If an item other than
[VIDEO-REC] is selected, no settings are changed.
[30%]…[107%]
f Factory setting: [30%]
[BLACK GAMMA] Sets the gamma curves of dark areas.
[−8]…[−1]: Compresses the dark areas.
[OFF]: Standard state
[1]…[8]: Expands the dark areas.
f Factory setting: [OFF]
[B. GAMMA RANGE] Sets the maximum level of compression/expansion.
[1]: About 20%
[2]: About 30%
[3]: About 40%
f Factory setting: [1]
[KNEE SETTING] [MANUAL KNEE] Selects the operation mode when the <OUTPUT>/<AUTO KNEE> selector switch is set to <OFF>.
[ON], [OFF]
f Factory setting: [ON]
[A.KNEE RESPONSE] Sets the auto knee response speed. The smaller the setting value, the faster the response speed is.
[1]…[8]
f Factory setting: [4]
[KNEE MASTER POINT] Sets the knee point position in 0.5% steps.
[70.0%]…[107.0%]
f Factory setting: [93.0%]
[KNEE MASTER
SLOPE]
Sets the knee inclination.
[0]…[99]
f Factory setting: [85]
[KNEE MASTER SLOPE
Rch]
Sets the knee inclination of Rch.
[−31]…[31]
f Factory setting: [0]
[KNEE MASTER SLOPE
Bch]
Sets the knee inclination of Bch.
[−31]…[31]
f Factory setting: [0]