32
Timer recording
Using SHOWVIEW* (G-CODE) number to make
timer recording
*SHOWVIEW : for Continental Europe.
G-
CODE : for Australia and N.Z..
G-
CODE and SHOWVIEW are different trademarks used to
represent the same easy recording feature. However, for
simplicity, only the term S
HOWVIEW will be used. If you use
G-
CODE system, follow the same steps listed for the SHOWVIEW
system.
[HDD] [RAM] [DVD-R]
Remote control only
You can easily programme the unit to make a timer recording of a
programme by entering the programme’s S
HOWVIEW (G-CODE)
number, which can be found in the television sections of
newspapers or in television guides. You can programme up to 32
programmes one month in advance. Programmes for everyday or
every week are counted as one programme.
Preparation
≥Switch [DVD, TV] (15) to “DVD”.
≥Ensure that this unit’s clock is set correctly.
≥(Make sure there is sufficient empty space on the disc for the
programme you are going to record plus a little extra.)
Recording to the HDD:
Confirm there is sufficient empty space for recording on the
HDD. (page 26)
Recording to the disc:
Insert a disc that can be written to.
- Check that disc can be recorded on (page 10).
- Ensure the write protect tab is not set to “PROTECT”
(page 87).
- Ensure the disc is not write-protected with DISC
INFORMATION (page 39).
1 Press [ShowView] ([G-Code]) (2) button.
<SHOWVIEW><G-CODE>
2 Press the numeric buttons (4) to enter the
S
HOWVIEW (G-CODE) number.
≥If you enter the wrong digit, use [2] (10) to move back and
enter the correct digit.
3 Press [ENTER] (10).
≥The Timer Programme Correction screen which allows you to
confirm the programme appears and make corrections if
necessary.
≥Check the programme.
To make corrections - Recording date, Recording time,
Recording mode or VPS/PDC setting etc (page 33).
To programme other recordings, repeat steps 1, 2, and 3.
4 Confirm that “HDD/DVD” is selected and use [3, 4]
(10) to select the recording drive (HDD/DVD).
5 If the programme is correct
Press [ENTER] (10).
≥The Timer Programme List screen appears.
6 Press [RETURN] (23).
ªTo put the unit on recording standby
Press [Á, TIMER] (12).
≥Ensure “Á” lights on the unit’s display.
≥The unit is not off. To save electricity, turn the unit off by pressing
[DVD, Í] (1).
≥If the unit is turned on when it is in timer recording standby mode,
a message screen will be displayed. When in this state the unit
can be used for playback* and JPEG operations, but it is not
possible to use the tuner on the unit to view television
broadcasts.
* The unit can only play the currently set TV system if the unit is
in timer recording standby mode.
ªIf “– –” appears under “Name” after entering a
S
HOWVIEW (G-CODE) number
Name stands for Programme Position/TV Station Name.
Normally, the name of the TV station or the number of the
programme position is displayed under “Name”.
However, if the TV station information was not automatically set
during Preset Downroad or Auto Setup due to adverse reception
conditions, the “– –” indication appears instead.
In such a case, follow the operation steps below to correct it.
Use [3, 4] (10) repeatedly to select the programme
position on which the TV programme to be recorded
will be broadcast.
After you have entered the information of a TV station, it remains
stored in the unit’s memory, and you do not need to enter it again
in the future.
RETURN
No.
ShowView
--
0 9
RETURN
No.
G-CODE
--
0 9
Enter ShowView Number by using 0-9 key. Enter G-CODE Number by using 0-9 key.
35:39 LP
Remain
HDD DVD
4:00 LP
16. 7 TUE12:53:00 16. 7 TUE12:53:00
35:39 LP
Remain
HDD DVD
4:00 LP
ShowView
1
1
1
1
11
1
1
G-CODE
1
1
1
1
11
1
11 1
35:39 LP
Remain
HDD DVD
4:00 LP 35:39 LP
Remain
HDD DVD
4:00 LP
16. 7 TUE12:53:00 16. 7 TUE12:53:00
RETURN
CANCEL
SELECT
Mode
StopStart
Name
Date
TIMER
RECORDING
ENTER
TIMER
RECORDING
Press ENTER to store new programme.
VPS
PDC
35:39 LP
Remain
HDD DVD
4:00 LP 35:39 LP
Remain
HDD DVD
4:00 LP
1 ARD 16/ 7 TUE 21:0020:00 SP
OFF
HDD
DVD
HDD
Title
RETURN
CANCEL
SELECT
Mode
StopStart
Name
Date
ENTER
Press ENTER to store new programme.
VPS
PDC
1 ARD 16/ 7 TUE 21:0020:00 SP
OFF
HDD
DVD
HDD
Title
16. 7 TUE12:53:00 16. 7 TUE12:53:00
RETURN
SELECT
TIMER
RECORDING
ENTER
CANCEL
35:39 LP
Remain
HDD DVD
4:00 LP
SP
OK
21:0020:001 ARD 16/ 7 TUE01
Mode
Disc
space
StopStartNo.
Name
Date
New Timer Programme
OFF
VPS
PDC
HDD
DVD
16. 7 TUE12:57:00
Timer standby is active, only playback is possible.
DVD(PAL).book32ページ２００３年５月１３日 火曜日 午後１２時３分
To Next Page
Loading...
