Panasonic KX-FP365CX

63
KX-FP365CX / KX-FM388CX
10 Test Mode
The codes listed below can be used to perform simple checks for some of the unit’s functions. When complaints are received
from customers, they provide an effective tool for identifying the locations and causes of malfunctions. To do this, you set the
Service mode (Refer to Operation Flow (P.66).) first, then operate the below test items.
Test Mode Type of Mode Code Function
Operation after code
input
MEMORY CLEAR Service Mode [5] [5] [0] Refer to Memory Clear Specification (P.69).
[SET]
FLASH MEMORY
CHECK
Service Mode [5] [5] [1] Indicates the version and checks the sum of the FLASH MEMORY.
[SET]
DTMF SINGLE
TONE TEST
Service Mode [5] [5] [2] Outputs the DTMF as single tones. Used to check the frequencies of the individ-
ual DTMF tones. Refer to DTMF Signal Tone Transmit Selection (P.64).
[1]....ON
[2]...OFF
MODEM TEST Service Mode [5] [5] [4] Telephone line circuit is connected automatically, output the following signals on
the circuit line.
1) OFF 2) 14400bps 3) 12000bps 4) 9600bps (V17) 5) 7200bps (V17)
6) 9600bps 7) 7200bps 8) 4800bps 9) 2400bps 10) 300bps 11) 2100Hz
12) 1100Hz
[SET]
SCAN CHECK Service Mode [5] [5] [5] Turns on the LEDs of the CIS and operates the read systems.
[SET]
MOTOR TEST Service Mode [5] [5] [6] Rotates the transmission and reception motor to check the operation of the motor.
00: Stop
13: TX
23: Pickup
33: Rx
43: Copy
• Press [STOP] button to quit.
[SET]
LED CHECK Service Mode [5] [5] [7] All LEDs above the operation panel board flash on and off, or are illuminated.
[SET]
LCD CHECK Service Mode [5] [5] [8] Checks the LCD indication.
Illuminates all the dots to check if they are normal.
[SET]
KEY CHECK Service Mode [5] [6] [1] Checks the button operation except “STOP” key.
Indicates the button code on the LCD while the button is pressed. Refer to But-
ton Code Table (P.64).
The available key is
any one that except
[STOP] key.
MEMORY CLEAR
(except History data)
Service Mode [7] [1] [0] Refer to Memory Clear Specification (P.69).
[SET]
VOICE PROMPT
TEST
Service Mode [7] [8] [4] You can hear the voice prompt from speaker after pressing [SET]” key.
[SET]
SENSOR CHECK &
VOX CHECK
Service Mode [8] [1] [5] If you enter this mode and operate sensor levers with your hands, the LCD dis-
play of the related sensor (or switch) turns ON / OFF. Also, when copying a docu-
ment, the related sensor will turn ON / OFF. (Do, Sn, Co, Pt, Vx)
For each sensor’s operation, refer to Sensors and Switches (P.33).
Do Sn Co Pt Vx
: LCD DISPLAY
Do: Document set sensor
:Turns on when the front cover us opened and a document is inserted.
Sn: Read position sensor.
:Turned on when the front cover is opened and starts to read a document.
Co: Cover open sensor
:Turned off when the cover is opened.
Pt: Paper top sensor
:Turned on when the cover is opened and detects a recording paper on the
right side end.
Vx: Vox signal
:Detection signal for the tone on the line. Turns on when there is a tone signal
on the line.
• Press [STOP] button to quit.
[SET]