68
KX-FP365CX / KX-FM388CX
580 TAM continuous tone detection 1: ON
2: OFF
1, 2 1 ON: Stops TAM operation when Dial tone, etc are
detected.
590 FAX auto redial time set × number of
times
00~99 05 Selects the number of redial times during FAX commu-
nication (not including the first dial).
591 FAX auto redial line disconnection time
set
× second 001~999 185 Sets the FAX redial interval during FAX communication.
592 CNG transmit select 1: OFF
2: ALL
3: AUTO
1~3 2 Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialing is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem (P.92).
593 Time between CED and 300bps 1: 75 msec
2: 500 msec
3: 1 sec
1~3 1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit / receive (P.94). Refer to Receive
Problem (P.93) and The unit can copy, but cannot
transmit / receive (P.94).
594 Overseas DIS detection select 1: Detects at
the 1st time
2: Detects at
the 2nd time
1, 2 1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit / receive (P.94). Refer to Sometime
there is a transmit problem (P.92) and The unit can
copy, but cannot transmit / receive (P.94).
595 Receive error limit value set 1: 5%
2: 10%
3: 15%
4: 20%
1~4 2 Sets the number of acceptable error lines when the
FAX reconstructs the received data. Refer to Receive
Problem (P.93).
596 Transmit level set × -1 dBm 00~15 11 Selects the FAX transmission level. Refer to Sometime
there is a transmit problem (P.92) and Receive Prob-
lem (P.93).
598 Receiving sensitivity × -1 dBm 20~48 42 Used when there is an error problem. Refer to The unit
can copy, but the transmission and reception image
are incorrect (P.97).
599 ECM frame size 1: 256 byte
2: 64 byte
1, 2 1 ----------
624 AT ring time out (KX-FM388 only) 1: 3 sec
2: 5 sec
1, 2 1 ----------
625 Setting printing density 1: Default
2: Lighter
3: Darker
1~3 1 The set value “2” means lighter than default density.
The set value “3” means darker than default density.
710 Memory clear except History data Refer to Memory Clear Specification (P.69).
717 Transmit speed select 1: 14400 BPS
2: 12000 BPS
3: 9600 BPS
4: 7200 BPS
5: 4800 BPS
6: 2400 BPS
1~6 1 Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.92) and The unit can copy, but the transmission
and reception image are incorrect (P.97).
718 Receive speed select 1: 14400 BPS
2: 12000 BPS
3: 9600 BPS
4: 7200 BPS
5: 4800 BPS
6: 2400 BPS
1~6 1 Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.93) and The unit
can copy, but the transmission and reception image
are incorrect (P.97).
722 Redial tone detect 1: ON
2: OFF
1, 2 1 Sets the tone detection mode after redialing.
724 PC-SEND busy tone detection
(KX-FM388 only)
1: ON
2: OFF
1, 2 2 ----------
745 Power ON film feed 1: ON
2: OFF
1, 2 1 When the power is turned on, the film is wound to take
up any slack.
763 CNG detect time for friendly reception 1: 10 sec
2: 20 sec
3: 30 sec
1~3 3 Selects the CNG detection tone of friendly reception.
773 DIS-DCS interval 1: 500 msec
2: 200 msec
1, 2 2 This is similar to #594. The time interval from receiving
DIS to sending DCS can be changed to wait for the
echo canceler to recover.
774 T4 timer × 100 msec 00~99 00 Use this function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
Code Function Set Value Effective
Range
Default Remarks
To Next Page
Loading...
