Feature Operations
Note
• If KX-UT113/KX-UT123/KX-UT133/KX-UT136
is connected to a Panasonic
KX-NS1000 PBX,
refer to the documentation of the KX-NS1000
for information about the operation of the unit.
However, please refer to this documentation for
details about the following features:
– Phonebook (Page 29, 40)
– Call Log (Page 30)
Making Calls
This section explains the basic methods for making a
call.
Making a Call
1. In stand-by mode, go off-hook.
2. Enter the number you want to call.
3. Press [ENTER], or wait a few seconds for the
number to be dialled.
4. To end the call, go on-hook.
Note
• For KX-UT113/KX-UT123,
if more than one line
is available at your unit, you can press
before going off-hook and then select the line
you want to use.
• For KX-UT133/KX-UT136/KX-UT248, if more
than one line is available at your unit, you can
press an idle DN button (flexible button)
assigned to the line you want to use before
entering the number. For details about DN
buttons, see "Flexible Buttons (KX-UT133/
KX-UT136/KX-UT248 only) (Page 39)".
Pre-dialling
In stand-by mode, you can start dialling (max. 32 digits)
while still on-hook.
• To delete a number you entered, press
.
• To clear the entire number, press and hold
.
• To
connect the call, go off-hook or press [ENTER].
Note
• For KX-UT133/KX-UT136/KX-UT248, you can
also
press an idle DN button (flexible button) to
connect the call. For details about DN buttons,
see "Flexible Buttons (KX-UT133/KX-UT136/
KX-UT248 only) (Page 39
)".
• For KX-UT113/KX-UT123, when pre-dialling
you can press
instead of going off-hook.
If more than one line is available at your unit,
select
the line to use, and then press [ENTER].
• If you receive an incoming call during
pre-dialling, the display changes to the
incoming call screen. For KX-UT133/
KX-UT136/KX-UT248, you can close the
incoming call screen by pressing
, and
continue pre-dialling.
Making a Call from the
Phonebook List
Scrolling through all entries
1. Press
.
2. Press [ ] or [ ] to select an entry.
3. Go off-hook.
4. To end the call, go on-hook.
Note
• For KX-UT133/KX-UT136/KX-UT248, you can
also press an idle DN button (flexible button) in
step 3 to connect the call. For details about DN
buttons, see "Flexible Buttons (KX-UT133/
KX-UT136/KX-UT248 only) (Page 39)".
• For KX-UT113/KX-UT123, you can press
instead of going off-hook. If more than
one line is available at your unit, select the line
to use, and then press [ENTER].
• In step 2, if multiple phone numbers are stored
for the entry, you can press
and then
select the phone number to call.
Searching by name
1. Press
.
2. Press
.
3. Enter the name (max. 12 characters) you want to
search for.
4. Press [ENTER].
The entry that matches your search appears.
5. Go off-hook.
6. To end the call, go on-hook.
Note
• For KX-UT113/KX-UT123, you can press
instead of going off-hook. If more than
Document Version 2013-03 Operating Instructions 29
Feature Operations
To Next Page
Loading...
