Panasonic MINAS A5E Series - Composition Of Peripheral Equipments

−
B39
−−
B38
−
English
LABEL
Terminal cover
(transparent)
2–ø4.5
R
Cx Cx
Cy
L L
Cy
2–ø4.5 x 6.75
53.1±1.0
100.0±2.0
88.0
75.0
5.0
12.0
10.0
50.0 60.0
7.0
2.0
(11.6)
(13.0)
6-M4
2
1
3
4
Circuit diagram
IN OUT
LABEL
A
B
C
H
10
F
E
D
G
M4
Cover
Body
4
5
1
2
63
L1
Cx1
IN OUT
R Cx1
Cy1
Earth terminal
M4
Screw for cover
M3
A B C D E F G H
115DV0PM20042
<DV0PM20042, DV0P4220> <DV0PM20043>
105 95 70 43 10 52 5.5
145DV0P4220 135 125 70 50 10 52 5.5
165DV0PM20043 136 165 90 80 40 54 5.5
Circuit
diagram
[Size]
[Unit: mm]
[Unit: mm]
LABEL
A
C
B
H
M5
E
F
D
Earth
terminal
M4
Screw for
cover
M3
G
Cover
Body
For single phase application, use 2 terminals among 3 terminals,
leaving the remaining terminal unconnected.
7. Conformity to EC Directives and UL Standards
Composition of Peripheral Equipments
Installation Environment
UsetheservodriverintheenvironmentofPollutionDegree1or2prescribedinIEC-
60664-1(e.g.InstallthedriverincontrolpanelwithIP54protectionstructure.)
Caution
UseoptionscorrectlyafterreadingOperatingInstructionsoftheoptions
tobetterunderstandtheprecautions.
Takecarenottoapplyexcessivestresstoeachoptionalpart.
Power Supply
100Vtype:Singlephase, 100V
+10%
to 120V
+10%
50/60Hz
(AtoC-frame)
  –15%

–15%
200Vtype:Single/3-phase, 200V
+10%
to 240V
+10%
50/60Hz
(AtoD-frame)
  –15%

–15%
200Vtype:3-phase, 200V
+10%
to 230V
+10%
50/60Hz
(E,F-frame)
  –15%

–15%
(1)Thisproductisdesignedtobeusedinover-voltagecategory(installationcategory)
IIIofEN61800-5-1:2007.
(2)UseaninsulatedpowersupplyofDC12to24VwhichhasCEmarkingorcomplies
withEN60950.
Circuit Breaker
InstallacircuitbreakerwhichcomplieswithIECStandardsandULrecognized(Listed
and
marked)betweenpowersupplyandnoiselter.
Integralsolidstateshortcircuitprotectiondoesnotprovidebranchcircuitprotection.
BranchcircuitprotectionmustbeprovidedinaccordancewiththeNationalElectrical
Codeandanyadditionallocalcodes.
Noise Filter
Whenyouinstallonenoiselteratthepowersupplyformulti-axesapplication,consultwith
manufacturerofthenoiselter.Ifsufcientnoisemarginisrequired,connect2ltersinseries.
• Optional parts
Option part No.
Voltage specications
for driver
Manufacturer’s
part No.
Applicable
driver (frame)
Manufacturer
DV0P4170 Singlephase100V/200V SUP-EK5-ER-6 AandB-frame OkayaElectricInd.
7. Conformity to EC Directives and UL Standards
Composition of Peripheral Equipments
Metallic control box
Controller
Insulated power supply
for interface
Power
supply
Surge
absorber
Noise filter
Noise filter for signal lines
*1
Ground (PE)
L1
U
X4
XA
XB
X6
M
RE
V
W
L2
L3
L1C
L2C
Noise filter for
signal lines
Noise filter for
signal lines
Noise filter for
signal lines
Noise filter for signal lines
Driver
Motor
Residual
current
device
(RCD)
Circuit
breaker
*1 A to D-frame: Noise filter for signal lines, E, F-frame: Noise filter for signal lines <Power supply cable>
Option part No.
Voltage specications
for driver
Manufacturer’s
part No.
Applicable
driver (frame)
Manufacturer
DV0PM20042
3-phase200V
3SUP-HU10-ER-6
A,B-frame
OkayaElectricInd.
Singlephase100V/200V
3-phase200V
C-frame
DV0P4220 Single/3-phase200V
3SUP-HU30-ER-6 D-frame
DV0PM20043 3-phase200V
3SUP-HU50-ER-6 E-frame