Panasonic PT-RQ22K

Chapter 4 Settings — [DISPLAY OPTION] menu
126 - ENGLISH
Primary input Secondary input
Number of signals
constructing one
screen
Details
[OFF] ― Disables the backup function.
[SDI1] [SDI2]
1
Enables the backup function.
[HDMI1 [SLOT1]]
*1
[HDMI2 [SLOT1]]
*1
[HDMI3 [SLOT2]]
*2
[HDMI4 [SLOT2]]
*2
[DVI-D1 [SLOT1]]
*1
[DVI-D2 [SLOT1]]
*1
[DVI-D3 [SLOT2]]
*2
[DVI-D4 [SLOT2]]
*2
[SDI1 [SLOT1]]
*3
[SDI2 [SLOT1]]
*3
[SDI3 [SLOT2]]
*4
[SDI4 [SLOT2]]
*4
[SDI1 [SLOT1]]
*5
[SDI3 [SLOT1]]
*5
[SDI1 [SLOT2]]
*6
[SDI3 [SLOT2]]
*6
[SDI1-2] [SDI3-4]
2
[HDMI1-2 [SLOT1]]
*7
[HDMI3-4 [SLOT2]]
*7
[DVI-D1-2 [SLOT1]]
*7
[DVI-D3-4 [SLOT2]]
*7
[SDI1-2 [SLOT1]]
*8
[SDI3-4 [SLOT2]]
*8
[SDI1-2-3-4]
*8
[SDI1-2-3-4 [SLOT1/2]]
*8
4[SDI1-2-3-4]
*5
[SDI1-2-3-4 [SLOT1]]
*5
[SDI1-2-3-4]
*6
[SDI1-2-3-4 [SLOT2]]
*6
*1 This is displayed when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This is displayed when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G) is installed in <SLOT 1>.
*4 This is displayed when the optional 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G) is installed in <SLOT 2>.
*5 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1>.
*6 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 2>.
*7 This is displayed when the optional Interface Boards equipped with corresponding input are installed in <SLOT 1> and <SLOT 2>.
*8 This is displayed when the optional 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G) is installed in <SLOT 1> and <SLOT 2>.
6) Press the <MENU> button.
f The [BACKUP INPUT SETTING] screen is displayed.
7) Press as to select [AUTOMATIC SWITCHING].
f When [BACKUP INPUT MODE] is set to [OFF], [AUTOMATIC SWITCHING] cannot be selected.
8) Press qw to switch the item.
f The items will switch each time you press the button.
[ENABLE]
Switches to the secondary input (primary input) automatically when the input signal for primary input
(secondary input) is disrupted.
[DISABLE] Disables the automatic input switching function.
Note
f The backup function is enabled when [BACKUP INPUT MODE] is set to anything other than [OFF] and same signal is input to the primary
input and the secondary input.
f To switch to the backup input signal using the backup function, make sure that the following three conditions are satised to be ready to use
the function.
g Set [BACKUP INPUT MODE] to anything other than [OFF].
g Input the same signal to the primary and secondary inputs.
g Display the image of the primary input or secondary input.
f If the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to
use the backup function is canceled. To switch to the backup input signal using the backup function again, switch to the primary input or
secondary input.
f When [BACKUP INPUT MODE] is set to anything other than [OFF], the combination of that input is displayed in [PRIMARY INPUT] and
[SECONDARY INPUT] of the [BACKUP INPUT SETTING] screen.
f [BACKUP INPUT STATUS] is displayed in the input guide (x page 149) and the [STATUS] screen (x pages 91, 185) when [BACKUP
INPUT MODE] is set to anything other than [OFF].
When the signal can be switched to the backup input signal using the backup function, [ACTIVE] is displayed in [BACKUP INPUT STATUS].
When it is not possible, [INACTIVE] is displayed instead.
The secondary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the primary
input is displayed.
The primary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the secondary
input is displayed.
f When [BACKUP INPUT MODE] is set to anything other than [OFF], the input is switched seamlessly if the input is switched between the
primary input and the secondary input while it is possible to switch to the backup input signal.