Panasonic PT-RQ22K

Chapter 4 Settings — [DISPLAY OPTION] menu
128 - ENGLISH
f [SIMUL INPUT SETTING] cannot be set when the [POSITION] menu → [GEOMETRY] is set to anything other than [OFF]. To input and
project the video signal in simultaneous format, use a at screen so that the geometric adjustment is unnecessary, and install the projector
so that the projected image will be rectangular.
f [SIMUL INPUT SETTING] cannot be set when the [ADVANCED MENU] menu → [BLANKING] → [CUSTOM MASKING] is set to anything
other than [OFF] ([PC-1], [PC-2], [PC-3]).
[CUSTOM MASKING] uses the masking function of the Panasonic computer application.
f [SIMUL INPUT SETTING] cannot be set when the [MULTI DISPLAY] menu → [MULTI DISPLAY MODE] is set to anything other than [OFF]
and displaying the four-screen display.
f This may not function properly for some connected external devices.
f This may not function properly depending on the signal.
r [SIMUL INPUT SETTING] screen
Usage of each input signal is displayed under the setting items of [SDI IN] and [SLOT IN] in the [SIMUL INPUT
SETTING] screen when [AUTO(x2-speed)] or [AUTO(x4-speed)] is set.
[SIMUL INPUT SETTING] Usage of the input signal Details
[AUTO(x2-speed)]
[1st FRAME INPUT]
Uses the signal for the corresponding input as a signal for the odd
frame.
[2nd FRAME INPUT]
Uses the signal for the corresponding input as a signal for the even
frame.
[AUTO(x4-speed)]
[1st FRAME INPUT]
Uses the signal for the corresponding input as the signal for the rst
frame (1 + n x 4).
[2nd FRAME INPUT]
Uses the signal for the corresponding input as the signal for the
second frame (2 + n x 4).
[3rd FRAME INPUT]
Uses the signal for the corresponding input as the signal for the
third frame (3 + n x 4).
[4th FRAME INPUT]
Uses the signal for the corresponding input as the signal for the
fourth frame (4 + n x 4).
[SDI IN]
Set this item in accordance with the signal input to the <SDI IN 1>/<SDI IN 2>/<SDI IN 3>/<SDI IN 4> terminal.
Setting [SDI LINK] in [SDI IN]
1) Press as to select [SDI IN].
2) Press the <ENTER> button.
f The [SDI IN] screen is displayed.
3) Press as to select [SDI LINK].
4) Press the <ENTER> button.
f The [SDI LINK] screen is displayed.
5) Press as to select the setting.
[AUTO] Automatically selects the single link, the dual link, or the quad link.
[SINGLE] Sets each of the SDI1 input, the SDI2 input, the SDI3 input, and the SDI4 input to single link.
[DUAL/SINGLE]
Sets the SDI1 input and the SDI2 input to dual link, and the SDI3 input and the SDI4 input to single
link.
[SINGLE/DUAL]
Sets the SDI1 input and the SDI2 input to single link, and the SDI3 input and the SDI4 input to dual
link.
[DUAL/DUAL] Sets the SDI1 input and the SDI2 input to dual link, and the SDI3 input and the SDI4 input to dual link.
[QUAD]
Sets the SDI1 input, the SDI2 input, the SDI3 input, and the SDI4 input to quad link.
(Factory default setting)
6) Press the <ENTER> button.
Note
f The single link is a setting to display one image with one input signal. The dual link is a setting to display one image with two input signals.
The quad link is a setting to display one image with four input signals.
f [SDI LINK] is xed to [SINGLE] in the following cases.
g When the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] is set to anything other than [OFF]
g When the [MULTI DISPLAY] menu → [MULTI DISPLAY MODE] is set to anything other than [OFF] and displaying the four-screen display
f The [SDI LINK] setting cannot be changed when the [DISPLAY OPTION] menu → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE]
is set as the combination to use the SDI input equipped on the projector as standard.