Panasonic PT-RQ22K

Chapter 4 Settings — [PROJECTOR SETUP] menu
186 - ENGLISH
[SERIAL NUMBER] Displays the serial number of the projector.
[PROJECTOR RUNTIME] Displays the runtime of the projector.
[LIGHT RUNTIME] Displays the runtime of the light source 1 and the light source 2.
[CONTINUOUS LIGHTING
TIME]
Displays the elapsed time from when the light source is illuminated.
The elapsed time after the illumination of the light source can be conrmed when adjusting the focus.
The elapsed time is reset when the light source is temporarily turned off such as using the shutter
function.
[MAIN/SUB VERSION] Displays the main and sub versions of the rmware of the projector.
[INTAKE AIR TEMP.]
*1
Displays the status of the intake air temperature of the projector.
[OPTICS MODULE TEMP.]
*1
Displays the status of the internal temperature of the projector.
[EXHAUST AIR TEMP.]
*1
Displays the status of the exhaust air temperature of the projector.
[LIGHT1 TEMP.]
*1
Displays the light source 1 temperature status of the projector.
[LIGHT2 TEMP.]
*1
Displays the light source 2 temperature status of the projector.
[SELF TEST] Displays the status of the projector.
[INPUT]
Displays the input terminal currently selected.
Displays the representative input terminal when one image is displayed with multiple input signals.
[SIGNAL NAME] Displays the input signal name.
[MEMORY NO.] Displays the memory number of the input signal.
[BACKUP INPUT STATUS]
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 125)
[NUMBER OF REGISTERED
SIGNAL]
Displays the number of registered signals.
[COOLING CONDITION] Displays the set cooling conditions.
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS] Displays the control status of the REMOTE2.
[AC VOLTAGE] Displays the input supply voltage.
[LENS TYPE]
*2
Displays the type name (type of the projection lens) set to the projection lens.
[LENS ID]
*2
Displays the ID set to the projection lens.
[LENS NAME]
*2
Displays the name set to the projection lens.
[LENS THROW RATIO]
*2
Displays the range of throw ratio supported by the projection lens in accordance with the [LENS
TYPE] setting.
[LENS ZOOM TYPE]
*2
Displays the drive method of the zoom motor attached to the projection lens.
[ZOOM CALIBRATION]
*2
Displays the zoom calibration result ([OK]/[FAILED]) and the calibration date.
[ON COUNT]
[POWER ON TIMES] Displays the number of times the power is turned on.
[MECHANICAL SHUTTER]
Displays the number of times the mechanical shutter is closed.
It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].
[OPERATING MODE]
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
[NORMAL] Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
[ECO] Displays the runtime of the light source with [OPERATING MODE] set to [ECO].
[USER1] Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
[USER2] Displays the runtime of the light source with [OPERATING MODE] set to [USER2].
[USER3] Displays the runtime of the light source with [OPERATING MODE] set to [USER3].
[CONSOLIDATED RUNTIME]
*3
Converts the total runtime of the light sources with [OPERATING MODE] set to each item into the
time used with the [NORMAL] setting.
The converted runtime is used for a rough indication about when to perform maintenance when the
projector is used in combination of each item in [OPERATING MODE].
[UPGRADE KIT]
[ET-UK20]
Displays the activation status by the Upgrade Kit (Model No.:
ET-UK20).
[ET-CUK10]
Displays the activation status by the Auto Screen Adjustment
Upgrade Kit (Model No.: ET-CUK10).
[SLOT1]
Displays the product model number of the Interface Board installed in <SLOT 1>.
Also, the rmware version is displayed after the product model number.
[SLOT2]
Displays the product model number of the Interface Board installed in <SLOT 2>.
Also, the rmware version is displayed after the product model number.