Panasonic PT-RQ22K

Chapter 1 Preparation — About your projector
ENGLISH - 35
r 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G)
This board supports the SD-SDI signal, HD-SDI signal, and 3G-SDI signal.
1 2 3 4 5
1 <3G-SDI 2 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 4 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 2 IN> terminal/<3G-SDI 4 IN> terminal of this
board.
2 <3G-SDI 2 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 4 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input SDI signal.
3 <3G-SDI 1 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 3 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 1 IN> terminal/<3G-SDI 3 IN> terminal of this
board.
4 <3G-SDI 1 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 3 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input SDI signal.
5 Handle
Note
f This projector does not support audio output because it is not equipped with audio function. However, when SDI signal with audio is input to
the <3G-SDI 1 IN>/<3G-SDI 2 IN>/<3G-SDI 3 IN>/<3G-SDI 4 IN> terminal, a signal with audio is output from the <3G-SDI 1 OUT>/<3G-SDI
2 OUT>/<3G-SDI 3 OUT>/<3G-SDI 4 OUT> terminal.
f To use the 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G), it is necessary for the rmware version of the 3G-SDI Terminal
Board with Audio to be 2.00 or later. Conrm the rmware version of the 3G-SDI Terminal Board with Audio when it does not operate after
installing to the projector.
Consult your dealer regarding the version update to the latest rmware if the version is earlier than 2.00.
For details on how to conrm the rmware version, refer to “How to conrm the rmware version of the Interface Board (optional)”
(x page 36).
r Interface Board for 12G-SDI (Model No.: ET-MDN12G10)
This board supports the SD-SDI signal, HD-SDI signal, 3G-SDI signal, 6G-SDI signal, and 12G-SDI signal.
25 541 3
1 <SDI 1 IN> terminal
This is a terminal to input SDI signal (SD-SDI/
HD-SDI/3G-SDI/6G-SDI/12G-SDI).
2 <SDI 2 IN/1 OUT> terminal
This is a terminal to input SDI signal (SD-SDI/HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(SD-SDI/HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 1
IN> terminal of this board.
3 <SDI 3 IN> terminal
This is a terminal to input SDI signal (SD-SDI/
HD-SDI/3G-SDI/6G-SDI/12G-SDI).
4 <SDI 4 IN/3 OUT> terminal
This is a terminal to input SDI signal (SD-SDI/HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(SD-SDI/HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 3
IN> terminal of this board.
5 Handle
Note
f The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal.
f To use the <SDI 2 IN/1 OUT> terminal or the <SDI 4 IN/3 OUT> terminal as an output terminal, set the [DISPLAY OPTION] menu → [SLOT
IN] → [SDI MODE] to [OUTPUT].
f When the projector is in standby mode, a signal is not output from the <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal.
f Install this board in either <SLOT 1> or <SLOT 2>. When these boards are installed in both <SLOT 1> and <SLOT 2>, only the board
installed in <SLOT 1> can be used.