Parker ETH Series - Page 26

Commissioning
Operating / Mounting instruction
26 192-550003N10 ETH ATEX December 2019
ETH032 ETH050 ETH080
Mounting type
M05
M10
M16
M05
M10
M20
M05
M10
M32
Option H
Option J
Option N
M6 - A2-70
M8 - A2-70
M10 - A2-70
Screw
7
16
31
Screw tightening torque
1
[Nm]
8
11
14
Minimum screw-in depth
2
[mm]
Option H
Option J
Option N
M6 - 8.8
M8 - 8.8
M10 - 8.8
Screw
7.5
18
35
Screw tightening torque
1
[Nm]
9
12
15
Minimum screw-in depth
2
[mm]
Option B*
M6 - 12.9
M8 - 12.9
M12 - 12.9
Screw
16.5
47
160
3
160
3.4
160
3
Screw tightening torque
1
[Nm]
12
12
25
Minimum screw-in depth
2
[mm]
Option G*
M6 - 12.9
M8 - 12.9
M12 - 12.9
Screw
16.5
47
160
3
160
3.4
160
3
Screw tightening torque
1
[Nm]
12 12 25 Minimum screw-in depth
2
[mm]
Option R
(5
M6 - 8.8
M8 - 8.8
M10 - 8.8
Screw
9
19
39
Screw tightening torque
1
[Nm]
9
9
16
Minimum screw-in depth
2
[mm]
ETH100
ETH125
Mounting type
M10/M20
M10/M20
Option F*
not possible
not possible
Screw
not possible
not possible
Screw tightening torque
1
[Nm]
not possible
not possible
Minimum screw-in depth [mm]
Option F
M16 – 8.8
M20 – 8.8
Screw
80
180
Screw tightening torque
1
[Nm]
15
25
Minimum screw-in depth [mm]
Option F
M16 – A2-70
M20 – A2-70
Screw
80
180
Screw tightening torque
1
[Nm]
15
25
Minimum screw-in depth [mm]
Option E
Option C
M16 – 8.8
M20 – 8.8
Screw
80
180
Screw tightening torque
1
[Nm]
15
25
Minimum screw-in depth
2
[mm]
Option E
Option C
M16 – A2-70
M20 – A2-70
Screw
80
180
Screw tightening torque
1
[Nm]
15
25
Minimum screw-in depth
2
[mm]
Option H
Option J
Option N
M16 – 8.8
M20 – 8.8
Screw
80
180
Screw tightening torque
1
[Nm]
15
25
Minimum screw-in depth
2
[mm]
Option H
Option J
Option N
M16 – A2-70
M20 – A2-70
Screw
80
180
Screw tightening torque
1
[Nm]
15
25
Minimum screw-in depth
2
[mm]
Option B*
M16 – 10.9
M20 – 8.8
Screw
270
330
Screw tightening torque
1
[Nm]
20 25 Minimum screw-in depth
2
[mm]
Option G*
M16 – 10.9
M20 – 8.8
Screw
270
330
Screw tightening torque
1
[Nm]
20 25 Minimum screw-in depth
2
[mm]
* For protection classes "B" and "C", we recommend for instance a GEOMET® coated screw (thin layer
corrosion protection), which must be in strength class 12.9. For the ETH100&125, no GEOMET coated
screw is required. (as the bracket is not available in stainless steel).
1
torque controlled tightening
2
when screwing into S235 JRG1 grade steel
3
provide suitable washer under the screw head
4
Safety factor against slipping is 1.6 in this case. Otherwise, at least 1.8
5
for power transmission from rod guide to your application please use the dowel pins