To Next PageTo Next PageWhat to do if my Pelpro Pellet stove starts and stops frequently in automatic mode?
If your Pelpro Pellet stove starts and stops frequently in automatic mode, first determine if varying room temperatures are the cause due to doors or windows being opened and closed repeatedly. If so, correct the issue. You may also want to examine the stove body and inspect the ambient probe, ensuring at least 2” is exposed outside of the stove body.
What to do if my Pelpro PPC90 Stove will not light?
If your Pelpro Stove will not light, several factors could be at play. First, ensure the firepot holes are clean. Check that the ignitor is heating up properly (glowing orange). Inspect the stove body. Confirm that there is fuel in the hopper and that the lid is securely closed. Access the vacuum switch by removing the right side panel and ensure it's clear and properly connected. Verify that all exhaust blower connections are secure. Make sure the feed assembly and motor are free of any obstructions. Finally, check that the exhaust path is clear.
What does Error Number 2 mean on my Pelpro Pellet stove?
Error Number 2 on your Pelpro Pellet stove indicates that the exhaust temperature is either above or below the acceptable range, or there is an exhaust probe failure. It could also mean the probe is not plugged in. To solve this, try plugging the probe into the board. If that doesn't work, you may need to replace the component.
What does Error Number 4 mean on my Pelpro Pellet stove?
Error Number 4 on your Pelpro Pellet stove, indicates a missed ignition. This can happen due to: * Lack of fuel (hopper empty). * A jam in the feed. * The feed not turning. * A disconnected or failed feed motor. * A dirty firepot. * Issues with the igniter (no power or failed). * Debris in the igniter chamber. To resolve this, fill the hopper, inspect and clear any jams in the feed tube, inspect the feed motor circuit, clean the firepot, check the igniter leads, and clean any debris from the igniter chamber.
What does Error Number 7 mean on my Pelpro Pellet stove?
Error Number 7 on your Pelpro Pellet stove can be caused by several factors: * The feed motor may be locked on. * Non-approved fuel might be in use. * The exhaust temperature might have exceeded the allowable temperature. * There may be an issue with the convection blower. * The unit might be dirty. * There could be a failure of some component. * The installation configuration might be too tight, limiting air circulation. Solutions include replacing the control board if the feed motor does not turn off, reviewing the fuel being used, cleaning the unit, replacing components, and reviewing/moving the installation if necessary to improve air circulation.
What to do if my Pelpro Stove is plugged in but no response?
If your Pelpro Stove is plugged in but not responding, you should first check your home's circuit breaker. Then, reset the snap disc, which is located between the drop tube and hopper. Finally, visually inspect the wires, blowers, and power cord for any breaks or wear that could be causing a short circuit.
Why is my Pelpro PPC90 making a rumbling/whistling noise during operation?
If your Pelpro Stove is making rumbling or whistling noises during operation, make sure the exhaust path is clean and clear. You may also need to adjust the air/fuel ratio using the trim adjustment dial.
Why does my Pelpro PPC90 Stove have a slow or smoky start-up and/or lazy flame?
If your Pelpro Stove exhibits a slow or smoky start-up or a lazy flame, start by confirming that the exhaust path is clean. Clean your firepot and behind your baffles inside your firebox. Next, examine the stove body. Ensure the igniter is properly aligned and centered. Finally, check the fuel quality.
What to do if my Pelpro PPC90 fire starts but goes out?
If your Pelpro Stove starts and then goes out, make sure the firebox is clean. Ensure the firepot holes are clear. Inspect the stove body. Confirm that the exhaust probe is connected. Inspect and clean the exhaust outlet. Also, confirm the exhaust path is clean.
What to do if there is debris in the convection blower of my Pelpro PPC90?
If you find debris in the convection blower of your Pelpro Stove, remove the right side panel to access and remove the convection blower. Then, vacuum any debris from the fan blades and blower housing.
General| Type | Pellet Stove |
|---|---|
| BTU Output | 90, 000 BTU |
| Fuel Type | Wood Pellets |
| Ignition | Automatic |
| Blower | Variable Speed |
Defines safety alert symbols (DANGER, WARNING, CAUTION, Notice, Pro Tip) for hazard communication.
Details actions that void warranty and increase fire risk.
Warns about extreme heat from surfaces and glass, and precautions for children.
Lists essential tools, supplies, and safety equipment for installation and maintenance.
Explains the critical aspects of pellet vent pipe configuration for safe operation.
Details specific clearance requirements for the vent termination point.
Provides instructions for installing the stove's exhaust venting system.
Details rules for horizontal/vertical vent runs, elbows, and pipe lengths.
Guides users through the initial ignition sequence and expected operations.
Detailed steps to initiate fuel feed when the hopper is empty.
Highlights the importance of regular cleaning for stove performance.
Addresses problems related to power supply and electrical components.
Diagnoses issues caused by soot, ash, or other obstructions.
Explains specific error codes and their corresponding corrective actions.
