PEP Modular Computers VMP2 - A.4 VMP1-IO1 Front Panel

142 pages

Save Page as PDF

To Next Page

To Previous Page

VMP2 VMP1-IO1 Module (Optional)

A.4 VMP1-IO1 Front Panel

Figure A-2: VMP1-IO1 Front Panel

The VMP1-IO1 front panel is provided with a window for the insertion of a PMC module

bezel.

VMP1-IO1

StockCheck.com

Main Page

Imprint2
Table of Contents3
List of Tables9
Proprietary Note15
Trademarks15
Explanation of Symbols16
For Your Safety17
Two Year Warranty19
Introduction23
Board Introduction24
Board Overview25
VMP2 Main Specifications26
Applied Standards28
CE Compliance28
Mechanical Compliance28
Environmental Tests28
Related Publications28
VME Systems/Boards28
PMC Add-On Modules/Carriers28
Functional Description31
Functional Block Diagram31
Front Panels32
Board Layout33
VMP2 Board (Front View)33
VMP2 Board (Reverse View)33
Main Features34
Cpu34
MPC8245 (Kahlua II) Features34
Memory36
System Memory (DRAM)36
Flash36
Eeprom36
Memory Expansion Socket (DIL600)36
Board Interfaces37
VME Interface and Connector Pinout37
VME Connector CON137
VME Bus Connector CON1 Pinout38
Pin Assignment J1/P1 VME Connector CON138
Ethernet Interface and Connector Pinout39
Ethernet Connector CON8 Pinout39
Ethernet RJ45 Connector CON8 Pin Assignment39
Ethernet Connector CON839
Serial Interfaces and Connectorpinout40
Pinouts of Serial Ports (RJ45 Connectors)40
Serial Port Connectors CON6 and CON740
PCI Expansion Interface and Connector Pinout41
PCI Expansion Connector CON1141
PCI Expansion Connector (CON11) Pinout42
PCI Expansion Connector Pinout42
Serial Interface Expansion Connector and Pinout44
Serial Interface Expansion Connector CON3 Pinout44
Serial Interface Expansion Connector (CON3) Pinout44
Memory Expansion Interface44
Memory Expansion Connector IC844
DEBUG Interface and Connector Pinout45
Debug Connector CON10 Pinout45
Digital Temperature Sensor (LM75)45
Debug Interface Connector (CON10) Pinout45
DEBUG Connector CON1045
Special Board Features46
Watchdog Timer46
Rtc (Stc M41T56)46
Reset/Abort46
Front Panel Led's47
Installation51
Board Installation51
Front Panel I/O Connectors52
Configuration55
Jumper Settings55
Bootstrap Loader / Socket Jumper J155
RTC (Real-Time Clock) Calibration Output (J2)55
Bootstrap Loader / Socket Jumper J1 Settings55
Resistor Setting for Non-Standard Socket Devices56
RS485 Termination (Onboard Interface Only)56
Resistor Setting for Various Non-Standard Socket Devices56
Jumper Settings for RS485 Termination56
Pinouts57
Flash Socket Type Selection57
Socket Device Selection (Memory Expansion Socket IC8)57
DIL 32 Pinout for Various Devices57
Serial Interface Expansion Connector (CON3)58
RS Expansion Connector Pinout58
Board Address Map59
Address Map Overview59
VMP2 Address Map59
VME Address Area60
Onboard Device Addresses61
VMP2 Device Address Map61
Special Registers Overview62
Board Control Registers62
Board ID Register62
Software Compatibility ID63
Memory Configuration Register64
Flash Bank Select Register64
Watchdog Control Register65
Control Register66
Event Register67
Board / Logic Revision Register68
Board Logic / Revision Register68
UART a / Registers69
General Register Set (THR/RHR, IER/ISR, MCR/MSR, LCR/LSR, SPR)69
Baud Rate Register Set (DLL/DLM)69
Enhanced Register Set69
UART B / Registers70
General Register Set (THR/RHR, IER/ISR, MCR/MSR, LCR/LSR, SPR)70
Baud Rate Register Set (DLL/DLM)70
Enhanced Register Set70
IRQ Routing71
Serial Irq's71
Real-Time Clock72
Eeprom73
Digital Temperature Sensor73
Netbootloader75
General Operation77
Netbootloader Interfaces77
ABT (Abort) Switch78
TERM Serial Interface78
SER0 Serial Interface78
Ethernet Interface78
Netbootloader Functions78
Netbootloader Control79
System Status Monitoring79
Netbootloader Control Commands79
System Status Monitoring Commands79
Ftp Server Access80
FLASH Operation80
Motorola S-Records80
Ftp Server Commands80
FLASH Operation Commands80
Motorola S-Records Commands80
Operating the Netbootloader81
Initial Setup81
Accessing the Netbootloader81
Netbootloader Configuration82
Net82
Passwd82
Telnet Login83
FLASH Operations83
FLASH Offsets83
Programming an Application84
Ftp Server Access84
Motorola S-Records84
Updating the Netbootloader85
Updating with an Image Loaded Via an Ftp Server85
Updating Via a Separate DIL FLASH85
Uploading a FLASH Area86
Plug and Play86
Porting an Operating System to the CPU Board86
Commands87
VMP1-IO1 Module (Optional)106
Overview107
Board Interfaces108
Board Layout109
VMP1-IO1 Front Panel110
Technical Specifications111
Board Installation112
Pinouts114
Jn1 (CON4) Pin Assignment114
Jn1, 32-Bit PCI114
Jn2 (CON5) Pin Assignment115
Jn2, 32-Bit PCI115
Jumper Setting116
VMP1-Post (Optional)118
Optoisolation RS485 Module (Optional)122
View of Underside of RS485 Module123
JTAG Subsystem125
Serial Port Pinout131
View of Underside of the CP320-TR1 Module131
Serial Port Pinout136
View of Underside of CP320-TR2 Module136

PEP Modular Computers VMP2 - A.4 VMP1-IO1 Front Panel

Table of Contents