LIST
OF ILLUSTRATIONS
Figure
Aerofiche
Grid No
2-1.
2-2.
2-3.
2-4.
2-4a.
2-4b.
2-4c.
2-5.
2-6.
2-7.
2-8.
2-9.
2-9a.
2-10.
2-11.
2-12.
2-13.
2-14.
2-15.
2-16.
2-17.
2-18.
3-1.
3-2.
4-1.
4-2.
4-3.
4-4.
4-4a.
4-5.
4-6.
4-7.
4-8.
4-9.
4-10.
4-11.
4-12.
4-13.
4-14.
4-15.
4-16.
4-17.
5-1.
5-la.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
Three View
of PA-32RT-300 ...............................
Three View of PA-32RT-300T ......... ..................
Station Reference Lines (PA-32RT-300) .....................
Station Reference Lines (PA-32RT-300T) ...................
Torque Wrench
Formula ..................................
Hose and Line Markings ..................................
Removal of Cherrylock Rivet ..............................
Access Plates
and Panels ..................................
Jacking Arrangement ....................................
Weighing the Airplane ....................................
Leveling Longitudinally
...................................
Leveling
Laterally ........................................
Tire Balancer ............................................
Lubrication
Chart (Landing Gear,
Main) ....................
Lubrication Chart (Landing Gear, Nose).....................
Lubrication Chart (Control System) ........................
Lubrication
Chart (Control System)
(cont ...................
.......
.......
.......
.......
.. .... .
.... ..
.......
.......
.......
.......
.......
. .... ..
.......
. . . . . .. .
..........
..........
..........
..........
..........
..... ....
..........
..........
..........
..........
..........
..........
..........
..........
.. . . ... ..
Lubrication
Chart (Control System)
(cont) ....................................
Lubrication Chart (Air Conditioning
Condenser) ..............................
Lubrication Chart (Cabin Door,
Baggage Door & Seat) ........................
Lubrication Chart (Power Plant, Propeller & Control Pivot Points) ..............
Lubrication
Chart (Back-up Extender
& Fuel Selector) .........................
Exhaust System
Inspection Points (PA-32RT-300)
.............................
Flap Control Cable
Attachment Bolt
Inspection ...............................
Aileron and Flap
Installation ...............................................
Wing Installation ..........................................................
Empennage
Group .........
...............................................
Landing
Light Assembly
..........................................
Snubber
Installation .......................................................
Skin
Material and Thickness ................................................
Surface
Scratches, Abrasions
or Ground-in-Dirt
...............................
Deep Scratches,
Shallow Nicks
and Small Holes...............................
Mixing of Epoxy
Patching Compound .......................................
Welding
Repair Method ...................................................
Repairing of Cracks........................................................
Various Repairs...........................................................
Repair
of Stress Lines
......................................................
Repair
of Impacted Damage
................................................
Control Surface Balance
Tool ...............................................
Aileron Balancing .........................................................
Rudder Balancing
.........................................................
Stabilator Balancing
.......................................................
Control
Column Assembly ...................
...........................
Correct Method of Installing
Rod End Bearings ...............................
Aileron
Controls (Typical)
..................................................
Bellcrank Rigging Tool ...................
..................................
Aileron
Rigging Tool ......................................................
Stabilator Controls ........................................................
Stabilator Rigging
Tool ....................................................
Stabilator
Travel Adjustments
...............................................
1A18
IA19
1A20
1A21
1B6
1B8
IB18
1B19
1B21
1B22
1B23
1B23
IC5
1C18
1C19
IC20
C21
1C22
1C23
1C24
IDI
1D2
1D9
1D10
1E1
1E3
IE5
IE9
1E11
IE14
1E21
1E21
1E22
1E22
1E24
IFI
1F2
1F2
IF6
IF8
IF9
IF10
1F16
1F17
IF21
1GI
IGI
1G2
1G6
1G7
Revised:
10/3/80
1A4