Pyronix ATLAS 8 PLUS

To Next Page

To Previous Page

12.11.50 Exiting Engineer Mode 53

12.11.51 System Faults 53

13. TECHNICAL SPECIFICATION

13.1 Power supply

13.2 Control PCB

13.3 Mechanical

13.4 Environmental

13.5 Cleaning

4. ENGINEER QUICK REFERENCE PROGRAMMING 55

5. COMMUNICATION PROGRAMMING

ATLAS 8 PLUS SERVICE HISTORY

8 ZONE PROGRAMMING LABEL

Page 6

Main Page

Table of Contents3
Introduction7
Safety8
Access Levels10
User10
Engineer10
Functional Description11
Operating Modes11
Entry / Exit Mode11
Zones12
Engineer Programmable Zones12
Dial out Reporting12
Functions13
Installation and Wiring18
PCB Layout18
PANEL ASSEMBLY - Polymere20
Speaker Assembly20
PANEL ASSEMBLY - Metal21
Tamper Switch21
Power Connections23
Mains Connection23
Battery Connection23
Bell, Strobe and Extension Speaker Connections23
Remote Keypad 'RKP' Connections23
Programmable Outputs23
Digital Communicators24
Auxiliary and Push to Set24
Tamper24
Tamper Connection for Bell Box's with Negative Removed Tamper24
Shock Sensors24
Double End of Line Resistor26
Wiring Unused Zones in Double End of Line26
Wiring Two or more Sensors with End of Line Resistors to a Single Zone26
Telephone Connections26
Battery Capacity27
Factory Defaults31
Entering Engineer Mode32
Setting Volume Control32
Resetting the Non-Volatile Memory (NVM) to Factory Settings32
Setting the Panel When Mains Fails32
Programming Set Modes33
Setting the Alarm Bell Time33
Setting Entry Time33
Setting Exit Time33
Changing the Engineer Code33
Programming Options33
Programmable Output33
Programmable Output34
System Option34
Programmable Re-Sets34
Alarm Receiving Centre Second Telephone Number35
Downloading Access Code35
Zone Alarm Reporting Codes35
System Set / Unset Reporting Codes36
User Set Reporting Codes36
User Unset Reporting Codes38
Maintenance and Priority Codes38
Restoral Reporting Codes38
Digicom Codes39
Keyswitch Set Configuration39
Group Reporting Telephone Allocation39
Engineer NVM Reset39
Follow Select39
Bell Delay40
Anti Code First Digit40
Engineers P.C. Third Telephone Number40
System Option40
Communicator Test41
Miscellaneous Reporting Codes41
Set a Set Option43
Set B Set Option43
Set C Set Option43
Set D Set Option43
Final Door44
Exiting Engineer Mode44
Systems Faults44
Atlas 8 Plus Lcd - Programming46
Factory Defaults46
Entering Engineer Mode48
Setting Volume Control48
Resetting the Non-Volatile Memory (NVM) to Factory Settings48
Setting the Panel When Mains Fails48
Programming Set Modes49
Setting the Alarm Bell Time49
Setting Entry Time49
Setting Exit Time49
Changing the Engineer Code49
Programming Options50
Programmable Output50
System Option50
Programmable Re-Sets51
Alarm Receiving Centre Telephone Number51
Alarm Receiving Centre Second Telephone Number51
Downloading Access Code51
Zone Alarm Reporting Codes51
System Set / Unset Reporting Codes52
User Set Reporting Codes52
User Unset Reporting Codes53
Maintenance and Priority Codes53
Restoral Reporting Codes53
Digicom Codes54
Keyswitch Set Configuration54
Group Reporting Telephone Allocation54
Engineer NVM Reset54
Follow Select54
Bell Delay54
Engineers P.C. Third Telephone Number55
System Option55
Communicator Test56
Miscellaneous Reporting Codes56
System Option58
Exiting Engineer Mode59
System Faults59
Technical Specification60
Power Supply60
Control PCB60
Mechanical60
Environmental60
Cleaning60
Engineer Quick Reference Programming61
Communication Programming63
Atlas 8 Plus Service History68

Pyronix ATLAS 8 PLUS - Page 6

Table of Contents

Related product manuals