What to do if Quinton TM55 Treadmill belt stops and an over-current error code appears?
If the Quinton Treadmill belt stops and an over-current error code appears, it might be due to stopping the belt for more than 2 seconds when it is set to ON. To resolve this: 1. Avoid stopping the belt for longer than 2 seconds. 2. Replace the deck and belt.
Why is my Quinton TM55 Treadmill making a squealing sound?
If your Quinton Treadmill is making a squealing sound, similar to a loose automobile fan belt, it's likely that the drive belt is loose. Try adjusting the belt tension. If the squealing persists, consider replacing the belt.
How to fix a squealing sound and walking belt slowing on Quinton Treadmill?
If your Quinton Treadmill is making a squealing sound similar to an automobile fan belt, and the walking belt slows when your foot strikes the deck, the drive motor belt (poly-V drive belt) is likely slipping. To fix this, adjust the belt tension or replace the belt.
How to fix popping during grade change on Quinton Treadmill?
If you're experiencing popping sounds during grade changes on your Quinton Treadmill, it might be due to faulty elevation chain alignment. To resolve this, adjust the alignment of the sprockets.
What causes knocking or thumping sound on Quinton TM55?
A knocking or thumping sound on your Quinton Treadmill, with the rate increasing and decreasing with the walking belt speed, is likely due to the front or rear roller (pulley) assembly bearings. To resolve this, isolate and replace the faulty roller.
What to do if the walking belt slips on my Quinton TM55?
If the walking belt on your Quinton Treadmill slips while the front roller turns, it's likely due to improper belt tension. You should adjust the belt tension. If the problem continues after adjustment, contact an authorized technician for assistance.
Why won't my Quinton Treadmill change grade?
If your Quinton Treadmill will not change grade, the issue could be due to excess weight on the treadmill. Check Appendix B for the maximum load. If weight is not the issue, it may be an internal problem, and you should contact an authorized technician for service.
What to do if circuit breaker trips on Quinton TM55 Treadmill?
If your Quinton Treadmill's circuit breaker trips during normal operation, it indicates a power fault. In this case, service is required, and you should contact an authorized technician.
Why does the walking belt hesitate on my Quinton Treadmill?
If the walking belt on your Quinton Treadmill hesitates, and adjusting the walking belt tension doesn't help, the problem may be an internal drive belt slipping. Service is required, so contact an authorized technician.
Why Quinton Treadmill won't start?
Here are several reasons why your Quinton Treadmill might not be starting: * The treadmill might not be plugged in. If this is the case, plug the power cord into an appropriate outlet. * The circuit breaker on the treadmill might be set to Off. Set the treadmill circuit breaker to On. * The building circuit breaker might have tripped. Contact building maintenance to reset it. If the breaker trips again, check the outlet voltage and ensure the power at the outlet and breaker match the treadmill's rating. Also, check for a damaged power cord and replace the configuration plate if necessary. * The power to the stress monitor might not be on. Turn on the power to the stress monitor. * The power cord might be damaged. Remove the cord from the outlet and replace it. * A fuse in the ...
Outlines potential problems covered and areas to check for diagnosis.
Guides users through step-by-step troubleshooting using error codes.
Provides crucial warnings and safety precautions regarding high voltage.
Advises on avoiding burns from hot treadmill components.
Details safety precautions for mechanical parts like belts and gears.
Lists specialized tools required for repair and replacement procedures.
Step-by-step instructions for safely removing the treadmill hood.
Procedure for replacing the configuration plate module.
Procedure for replacing the AC Drive Module unit.
Detailed procedure for removing and replacing the poly-V drive belt.
Procedure for replacing the treadmill drive motor.
Instructions for removing and replacing the treadmill transformer.
Steps for replacing the treadmill's grade motor.
Detailed steps for replacing the grade potentiometer.
Procedure for dislodging and replacing a jammed rack gear.
Procedure for adjusting grade limit switches for proper operation.
Detailed steps for replacing the treadmill walking belt.
General safety precautions and warnings for operating the treadmill.
General| Motor Power | 3.0 HP |
|---|---|
| Speed | 0.5 - 12 mph |
| Incline | Yes |
| Incline Range | 0-15% |
| Maximum User Weight | 400 lbs |
| Weight Capacity | 400 lbs |
| Display | LED |
| Programs | 12 workout programs |
| Heart Rate Monitoring | Contact Grips |
To Next Page
