R&S ZNLE Series - Calculate

Command reference
R&S
®
ZNL/ZNLE
664User Manual 1178.5966.02 ─ 20
CALCulate<Chn>:LIMit:CLEar.........................................................................................666
CALCulate<Chn>:LIMit:CONTrol[:DATA]...........................................................................667
CALCulate<Chn>:LIMit:CONTrol:SHIFt............................................................................ 668
CALCulate<Chn>:LIMit:DATA..........................................................................................668
CALCulate<Chn>:LIMit:DCIRcle:CLEar............................................................................669
CALCulate<Chn>:LIMit:DCIRcle:DATA.............................................................................669
CALCulate<Chn>:LIMit:DCIRcle:DISPlay[:STATe]............................................................. 669
CALCulate<Chn>:LIMit:DCIRcle[:STATe].......................................................................... 670
CALCulate<Chn>:LIMit:DELete:ALL.................................................................................670
CALCulate<Chn>:LIMit:DISPlay[:STATe].......................................................................... 670
CALCulate<Chn>:LIMit:FAIL?..........................................................................................671
CALCulate:LIMit:FAIL:ALL?.............................................................................................671
CALCulate:LIMit:FAIL:DATA?.......................................................................................... 672
CALCulate<Chn>:LIMit:LOWer[:DATA]............................................................................. 672
CALCulate<Chn>:LIMit:UPPer[:DATA]..............................................................................672
CALCulate<Chn>:LIMit:LOWer:FEED.............................................................................. 673
CALCulate<Chn>:LIMit:UPPer:FEED...............................................................................673
CALCulate<Chn>:LIMit:LOWer:SHIFt...............................................................................674
CALCulate<Chn>:LIMit:UPPer:SHIFt............................................................................... 674
CALCulate:LIMit:POINts:LOWer?.................................................................................... 674
CALCulate:LIMit:POINts:UPPer?..................................................................................... 674
CALCulate<Chn>:LIMit:SEGMent<Seg>:AMPLitude:STARt................................................675
CALCulate<Chn>:LIMit:SEGMent<Seg>:AMPLitude:STOP................................................675
CALCulate<Chn>:LIMit:SEGMent:COUNt?.......................................................................676
CALCulate<Chn>:LIMit:SEGMent<Seg>:FORMula............................................................677
CALCulate<Chn>:LIMit:SEGMent<Seg>:FORMula:STATe..................................................677
CALCulate<Chn>:LIMit:SEGMent<Seg>:INTerpol............................................................. 678
CALCulate<Chn>:LIMit:SEGMent<Seg>:STIMulus:STARt..................................................678
CALCulate<Chn>:LIMit:SEGMent<Seg>:STIMulus:STOP.................................................. 678
CALCulate<Chn>:LIMit:SEGMent<Seg>:TYPE................................................................. 679
CALCulate<Chn>:LIMit:SOUNd[:STATe]...........................................................................679
CALCulate<Chn>:LIMit:STATe.........................................................................................680
CALCulate<Chn>:LIMit:STATe:AREA............................................................................... 680
CALCulate<Chn>:LIMit:TTLout<Pt>[:STATe]..................................................................... 681
CALCulate<Chn>:LIMit:CIRCle:CLEar
Resets the circle test for the active trace of channel <Chn>.
Suffix:
<Chn>
.
Channel number used to identify the active trace
Usage: Event
Manual operation: See "Clear Test" on page 447
CALCulate<Chn>:LIMit:CIRCle:DATA <CenterX>, <CenterY>, <Radius>
Defines a circle limit lines by its center coordinates and its radius.
VNA command reference