RichAuto A122 - Default Chapter; Table of Contents

Foreword
----------------------------------------------------------------------------------
1. RichAuto System C
onstruction
1.1 System C
onstruction.......................................................................................
1.2 Description of Each Component...................................................................
1.2.1 Handle..........
........................................................................................
1.2.2 Interface board
................................. ........................
1.3 Interface Board She
ll Installation Size...................................................
2. Buttons introduction
-----------------------------------------------------------
2.1 Buttons introduction..........................
2.2 Usage Methods
............................................................................................................
2.3 Detailed information for buttons
3. Wiring instructions
-------------------------------------------------------------
3.1 RichAuto
interface board
3.2 Interface board I / O ports description.....................................................................
3.3 Hardware wiring.......................
3.4 Commissioning of the Machine and Control system....................................
4. Menu description
----------------------------------------
4.1 Menu category......................................................................................................
4.2 Menu details.............
.............................
4.2.1 User parameter
Setup
4.2.2 File Operation
......................................................................................
4.2.3 System Setup
.............................................................................................
4.2.4 Factory Setup
..........................................................................
4.2.5 Version View...
.................................................................................................
5. Machine Operation
------------------------------------------------------------------------------------
5.1Return home……..
..........................................................................................................3
5.2 Import processing file........................................................................................
5.3 Manual processing Operation..............................................
5.3.1 Manual operation speed switching and adjusting
5.3.2 Manual
processing
5.3.3 Manual testing input and output
5.4Automatic processing operation......................................................................
5.4.1 Set workp
iece origin
5.4.2 Set stop position……………………………………………
5.4.3
Adjust the origin of the workpiece
5.4.4
Choose processing files
5.4.5
Set processing parameters
5.5 During processing
operations........................................................................................
5.5.1 Speed ratio adjusting
5.5.2 Pause & position adjusting
Beijing RichAuto S&T Co., Ltd
Content
----------------------------------------------------------------------------------
onstruction
----------------------------------------------------
onstruction.......................................................................................
1.2 Description of Each Component...................................................................
........................................................................................
................................. ........................
.........................
ll Installation Size...................................................
-----------------------------------------------------------
-------------------------
2.1 Buttons introduction..........................
.....................................
...............................
............................................................................................................
2.3 Detailed information for buttons
function................................
......................................8
-------------------------------------------------------------
------------------------
interface board
description..................................................
.........................
3.2 Interface board I / O ports description.....................................................................
3.3 Hardware wiring.......................
...........................................................................
3.4 Commissioning of the Machine and Control system....................................
----------------------------------------
---------------------
-------------------------
4.1 Menu category......................................................................................................
.............................
..........................................
..............................
Setup
...................................................................
......................................................................................
.............................................................................................
..........................................................................
..
..................
.................................................................................................
------------------------------------------------------------------------------------
..........................................................................................................3
5.2 Import processing file........................................................................................
5.3 Manual processing Operation..............................................
............................
5.3.1 Manual operation speed switching and adjusting
.................
.............................
processing
mode............................................................
........................
5.3.3 Manual testing input and output
.............................................................
5.4Automatic processing operation......................................................................
iece origin
....................................................................
................
5.4.2 Set stop position……………………………………………
…………………
Adjust the origin of the workpiece
.............
.................................................
Choose processing files
.............................................................
..........................
Set processing parameters
………………………………………………………
operations........................................................................................
5.5.1 Speed ratio adjusting
....................................................................
5.5.2 Pause & position adjusting
.
....................................................................
Beijing RichAuto S&T Co., Ltd
RichAuto |
----------------------------------------------------------------------------------
------------------1
----------------------------------------------------
-----------------3
onstruction.......................................................................................
...............3
1.2 Description of Each Component...................................................................
.................3
........................................................................................
.................3
.........................
....................4
ll Installation Size...................................................
........................5
-------------------------
6
...............................
.........6
............................................................................................................
...6
......................................8
------------------------
10
.........................
.10
3.2 Interface board I / O ports description.....................................................................
.......11
...........................................................................
...........13
3.4 Commissioning of the Machine and Control system....................................
..................17
-------------------------
18
4.1 Menu category......................................................................................................
..........18
..............................
.18
...................................................................
.......................18
......................................................................................
................23
.............................................................................................
..........24
..................
........25
.................................................................................................
..35
------------------------------------------------------------------------------------
35
..........................................................................................................3
5
5.2 Import processing file........................................................................................
............35
............................
..............35
.............................
.36
........................
37
.............................................................
............37
5.4Automatic processing operation......................................................................
..............38
................
........38
…………………
..39
.................................................
........39
..........................
40
………………………………………………………
40
operations........................................................................................
.41
....................................................................
.......................41
....................................................................
.............42