Rigol MSO5000-E Series

To Next Page

To Previous Page

Chapter 14 Waveform Recording & Playing                                                                                  RIGOL 
MSO5000-E User Guide  14-1 
Chapter 14 Waveform Recording & Playing 
 
Waveform recording & playing function can play the recorded waveforms of the 
analog input channels (CH1-CH2) and the digital channels (D0-D15), enabling you to 
analyze the waveforms better.   
 
Note: The horizontal timebase must be set to "YT" mode during waveform 
recording. 
 
Contents in this chapter: 
⚫  Common Settings 
⚫  Record Options 
⚫  Play Options 
 
 

Main Page

Safety Requirement4
- Safety Notices and Symbols6
- Measurement Category7
- Ventilation Requirement7
- Working Environment8
- Care and Cleaning9
- Environmental Considerations10
MSO5000-E Series Overview11
Document Overview12
- Table of Contents15
Chapter 1 Quick Start23
- General Inspection24
- Appearance and Dimensions25
- To Prepare for Use26
- Front Panel Overview32
- Rear Panel Overview33
- Front Panel Function Overview35
- User Interface41
- Touch Screen Controls44
- Parameter Setting Method48
- To Use the Kensington Security Lock49
- To Use the Built-In Help System50
- To View the Option Information and the Option Installation51
Chapter 2 To Set the Vertical System53
- To Enable or Disable the Analog Channel54
- To Adjust the Vertical Scale55
- Vertical Expansion56
- To Adjust the Vertical Offset56
- Channel Coupling57
- Bandwidth Limit57
- Probe Ratio58
- Input Impedance59
- Waveform Invert59
- Amplitude Unit60
- Channel Delay60
- Offset Cal61
- Channel Label62
Chapter 3 To Set the Horizontal System65
- To Adjust the Horizontal Timebase66
- To Adjust the Horizontal Position67
- Delayed Sweep68
Chapter 4 To Set the Sample System71
- Timebase Mode72
- Acquisition Mode75
- Sampling Mode77
- Sample Rate77
- LA Sample Rate79
- Memory Depth79
- LA Memory Depth80
- Anti-Aliasing80
- Horizontal Expansion81
Chapter 5 To Trigger the Oscilloscope83
- Trigger Source84
- Trigger Level/Threshold Level85
- Trigger Mode86
- Trigger Coupling87
- Trigger Holdoff88
- Noise Rejection89
- Trigger Type90
- Zone Trigger134
- Trigger Output Connector135
Chapter 6 Operations and Measurements137
- Math Operation138
- Auto Measurement163
- Cursor Measurement176
Chapter 7 Digital Voltmeter (DVM) and Frequency Counter187
- Digital Voltmeter (DVM)188
- Frequency Counter190
Chapter 8 Power Analysis (Option)193
- Power Quality194
- Ripple196
Chapter 9 Histogram Analysis199
- To Enable or Disable the Histogram Function200
- To Select the Histogram Type200
- To Select the Histogram Source201
- To Set the Histogram Height201
- To Set the Histogram Range201
- To Enable or Disable the Statistical Function201
- To Reset202
Chapter 10 Digital Channel203
- To Select the Digital Channel204
- To Enable/Disable the Digital Channel204
- To Set the Threshold and Calibrate Probe205
- Auto Arrangement Setting206
- To Set the Waveform Display Size206
- To Set the Label206
- Group Setting207
- Waveform Color of the Digital Channel208
Chapter 11 Protocol Decoding209
- Parallel Decoding210
- RS232 Decoding (Option)215
- I2C Decoding (Option)222
- SPI Decoding (Option)226
- LIN Decoding (Option)231
- CAN Decoding (Option)236
- Flexray Decoding (Option)241
- I2S Decoding (Option)245
- 1553B Decoding (Option)249
Chapter 12 Reference Waveform253
- To Enable Ref Function254
- To Select the Reference Channel254
- To Select the Ref Source254
- To Adjust the Ref Waveform Display254
- To Save to Internal Memory255
- To Clear the Display of the Reference Waveform255
- To View Details of the Reference Waveform255
- To Reset the Reference Waveform256
- Color Setting256
- Label Setting256
- To Export to Internal or External Memory257
- To Import from Internal or External Memory257
Chapter 13 Pass/Fail Test259
- To Enable or Disable the Pass/Fail Test Function260
- To Start or Stop the Pass/Fail Test Operation260
- To Select the Source260
- To Create a Mask261
- To Save the Mask261
- To Load a Mask261
- To Set the Output Form of the Test Results262
- To Enable or Disable the Display of the Statistics of the Test Results263
- Statistics Reset263
Chapter 14 Waveform Recording & Playing265
- Common Settings266
- Record Options267
- Play Options268
Chapter 15 Search and Navigation Function271
- Search Function272
- Navigation Function274
Chapter 16 Display Control277
- To Select the Display Type278
- To Set the Persistence Time278
- To Set the Waveform Intensity279
- To Set the Screen Grid279
- To Set the Grid Brightness279
- Scale280
- Color Grade280
- Waveform Freeze280
Chapter 17 Function/Arbitrary Waveform Generator (Option)281
- To Output Basic Waveforms282
- To Output the Arbitrary Waveform289
- Modulation293
  - Fsk296
- Sweep296
- Burst298
Chapter 18 Store and Load301
- Storage System302
- Storage Type302
- Load Type304
- Internal Storage and Load304
- External Storage and Load306
- Disk Management306
- Factory Settings313
Chapter 19 Bode Plot325
- To Enable the Bode Function326
- To Run or Stop the Operation326
- Parameter Setting327
- Cursor329
- Display Type329
  - Wave Form330
  - Chart330
- Display331
- Save331
- Connection Diagram331
Chapter 20 System Utility Function Setting333
- Remote Interface Configuration334
- System-Related339
Chapter 21 Remote Control353
- Remote Control Via USB354
- Remote Control Via LAN358
- Remote Control Via GPIB359
Chapter 22 Troubleshooting361
Chapter 23 Appendix363
- Appendix A: Accessories and Options363
- Appendix B: Warranty364
Index365

Table of Contents

Other manuals for Rigol MSO5000-E Series

Related product manuals