Rishabh RISH LM 1340 - Page 22

:
UP KEY
: DOWN KEY
: ENTER KEY
Setup Parameter Screens
SEL (Select)
Out PArA
(Output Parameter)
rELY1 out
(Relay 1 Output)
(Exit Menu)
rESEt
(Reset Parameter)
Ser PArA
(Serial Comm.Parameter)
dEV Addr
(Modbus Address)
bAud rAtE
(Baud Rate)
PritY
(Parity Bits)
CodE (PassWord
)
SYS PArA
(System Parameter)
(Sec 3.2.1)
(Sec 3.2.2)
(Sec 3.2.4)
(Sec 3.2.5)
(Sec 3.2.5.1)
(Sec 3.2.2.1)
(Sec 3.2.2.2)
(Sec 3.2.2.3)
SYS TYPE
(System Type / Network)
Pt.Pri
(PT Primary)
Pt.SEC
(PT Secondary)
Ct.Pri
Ct.SEC
intGr tiME
(Demand Integ. Time)
noiS E Cut oF
(Noise Current Cut-off)
Auto SCroL
(Auto Scrolling)
(Sec 3.2.1.1)
(Sec 3.2.1.2)
(Sec 3.2.1.3)
(Sec 3.2.1.4)
(Sec 3.2.1.5)
(Sec 3.2.1.7)
(Sec 3.2.1.8)
(Sec 3.2.1.9)
(Sec 3.2.5.1)
Edrc
EnrGY unit
(Energy Output)
(Sec 3.2.1.11)
(Sec 3.2.1.12)
(Energy digit reset count)
no oF PoLES
(No. of poles selection)
(Sec 3.2.1.10)
EnrG Y rAtE
(Sec 3.2.1.13)
(Energy rate)
(CT Primary)
(CT Secondary)
dGiP PArA
(Digital Input
dbnc tiME
(De-Bounce Time)
(Sec 3.2.7)
(Sec 3.2.7.1)
Parameter)
(Sec 3.2.7.2)
di-1 Mode
(Digital Input 1 Mode)
quit
User Para Menu)
(Sec 3.2.7.6)
rELY2 out
(Relay 2 Output)
(Sec 3.2.5.1)
SYS Freq
(System Frequency)
(Sec 3.2.1.6)
iMPL S rAt E
(Sec 3.2.1.14)
(Impulse Rate)
quit
(Sec 3.2.2.4)
(Exit Ser Para Menu)
HL Mn
(Health Monitor)
(Sec 3.2.6)
VoLt unbL
(Voltage Unbalance)
Curnt unbL
(Current Unbalance)
undEr FrEq
(Under Frquency)
(Sec 3.2.6.1)
(Sec 3.2.6.2)
(Sec 3.2.6.3)
quit
(Sec 3.2.6.7)
(Exit Health Monitor)
(Sec 3.2.7.3)
di-1 PMuL
(Pulse Multiplier)
(Exit
B
A
quit
Y
(Sec 3.2.7.4)
di-2 Mode
(Digital Input 2 Mode)
D
C
quit
(Sec 3.2.1.16)
(Exit Sys Para Menu)
VErS n
(Sec 3.2.1.15)
(Version Information)
undEr VoLt
(Under Voltage)
(Sec 3.2.6.4)
oVEr VoLt
(Over Voltage)
(Sec 3.2.6.5)
oVEr Curnt
(Over Current)
(Sec 3.2.6.6)
none (No Parameter),
ALL (All Parameters),
dmd (Demand),
EnrGY (Energy),
hiGh
(Max values),
LoW (Min values),
HourS (Run Hr. & On Hr.),
Intr (No. of Interrupts),
Select any one option
using “Enter” key.
tAriF (Tariff),
Di EC
To Exit, Select “none”.
(Digital Input
External Energy
Reset)
Pulse Mode
Is
Select
YES
NO
Pulse Mode
Is
Select
YES
NO
E
IP PArA*
(IP Parameter)
IP Addr
(IP Address)
Subnet Msk
(subnet Mask)
Default Gt
(Default gateway)
(Sec 3.2.3)
(Sec 3.2.3.1)
(Sec 3.2.3.2)
(Sec 3.2.3.3)
Ser Port
(Sec 3.2.3.4)
(Server Port)
quit
(Sec 3.2.3.5)
(Exit IP Para Menu)
C
D
Note*: IP Menu is available only
in case of Ethernet option.
(Sec 3.2.7.5)
di-2 PMuL
(Pulse Multiplier)
20