SAJ 8000m Series

Questions and Answers:

M
Michelle VegaAug 21, 2025
What to do if SAJ 8000m Controller shows E014 error?
- N
  Nancy BarajasAug 22, 2025
  If your SAJ Controller displays error E014, it could be due to several reasons. It may be caused by an instantaneous overcurrent, an output short circuit (in which case use a good wire), cooling fan issues (replace the fan or clear the ventilation), high ambient temperature (decrease it), loose cables or terminals (inspect and tighten them), a power circuit abnormality (ask for support), or a control PCB board abnormality. Refer to over current solutions.
J
Joshua SinghSep 4, 2025
What to do if SAJ 8000m shows E005 error?
- D
  Diana ReeseSep 4, 2025
  If your SAJ Controller displays error E005, it could be due to abnormal input voltage (inspect input power) or restarting the motor too quickly after an instantaneous trip-off (avoid prompt restart when trip-off).
J
Jason ChaseSep 2, 2025
What to do if SAJ Controller shows E023 error?
- H
  harrisrobinSep 2, 2025
  If your SAJ Controller is showing error E023, it could be due to accelerating too fast (increase acceleration time), restarting the motor too quickly after an instantaneous trip-off (avoid prompt restart when trip-off), low input voltage (inspect power grid), or the load being too heavy (select a larger capacity inverter).
J
John LawsonSep 1, 2025
What to do if SAJ Controller shows E006 error?
- P
  Phillip KnoxSep 1, 2025
  If the SAJ Controller is showing error E006, it could be due to decelerating too fast (increase deceleration time) or the load being too heavy with large inertia (add suitable braking units).
J
Jose WardAug 30, 2025
What to do if SAJ 8000m Controller shows E010 error?
- D
  Dr. Paul MoodyAug 30, 2025
  If your SAJ Controller shows error E010, it might be due to accelerating too fast (increase acceleration time), restarting the motor too quickly after a trip-off (avoid prompt restart when trip-off), low input voltage (inspect power grid), or the load being too heavy (select larger capacity drive).
C
chad04Aug 29, 2025
What to do if SAJ 8000m shows E003 error?
- J
  Jackson DavisAug 29, 2025
  If your SAJ Controller displays error E003, it may be because you are decelerating too fast (increase deceleration time), the load is too heavy and has large inertia (add suitable braking units), or the drive capacity is too low (select larger capacity drive).
J
Justin RoyAug 28, 2025
Why does my SAJ 8000m Controller show E004 error?
- E
  Erin SimmonsAug 28, 2025
  The E004 error on your SAJ Controller can be triggered by a sudden change of load (check the load), low input voltage (inspect the input power supply or wiring), or insufficient drive capacity (select a larger capacity drive).
S
Shaun CoxAug 27, 2025
What to do if SAJ Controller shows E011 error?
- M
  Michelle MartinAug 27, 2025
  If the SAJ Controller displays error E011, the possible causes include low input voltage (inspect the voltage of the power grid), improper setting of motor rated current (properly set the motor rated current), an improper motor’s overload protection threshold (inspect load and boost the torque), or the drive capacity being too low (select a larger capacity drive).
C
Christopher Davis Jr.Aug 25, 2025
What to do if SAJ Controller shows E002 error?
- M
  Mr. Jose Green DDSAug 26, 2025
  If the SAJ Controller shows error E002, it could be due to accelerating too fast (increase acceleration time), low input voltage (inspect the input power supply or wiring), or insufficient drive capacity (select a larger capacity drive).
A
Anthony MckenzieAug 23, 2025
What should I do if my SAJ Controller displays error E001?
- E
  Erika VillegasAug 23, 2025
  If your SAJ Controller shows error E001, it might be due to several reasons: the acceleration time being too short (increase acceleration time), a damaged IGBT module (ask for support), malfunction caused by interference (inspect external equipment and eliminate interference), or improper grounding (check grounding wire).