-38-
Electrical Adjustments
Group/
Item
Item Name Function Initial Range Note
150 PreCoast YCbCr 480i 7 0 - 63
151 PostCoast YCbCr 480i 13 0 - 63
152 PreCoast YCbCr 575i 7 0 - 63
153 PostCoast YCbCr 575i 13 0 - 63
154 PreCoast YCbCr 480p 7 0 - 63
155 PostCoast YCbCr 480p 13 0 - 63
156 PreCoast YCbCr 575p 7 0 - 63
157 PostCoast YCbCr 575p 13 0 - 63
158
PreCoast YCbCr 720p
60Hz
7 0 - 63
159
PostCoast YCbCr 720p
60Hz
13 0 - 63
160
PreCoast YCbCr 720p
50Hz
7 0 - 63
161
PostCoast YCbCr 720p
50Hz
13 0 - 63
162 PreCoast YCbCr 1080i 60Hz 7 0 - 63
163
PostCoast YCbCr 1080i
60Hz
13 0 - 63
164 PreCoast YCbCr 1080i 50Hz 7 0 - 63
165
PostCoast YCbCr 1080i
50Hz
13 0 - 63
166 PreCoast YCbCr 1035i 7 0 - 63
167 PostCoast YCbCr 1035i 13 0 - 63
180 PreCoast SCART 480i 7 0 - 63
181 PostCoast SCART 480i 13 0 - 63
182 PreCoast SCART 575i 7 0 - 63
183 PostCoast SCART 575i 13 0 - 63
Group
10
Sync Processor
0 SYNCAMPHLCKTOLOW
Minimum sync amplitude threshold
for HLCK 1 to 0 tansition
0x1000 0 - 9999
1 SYNCAMPHLCKTOHI
Minimum sync amplitude threshold
for HLCK 0 to 1 tansition
0x700 0 - 9999
Group
20
Video Decoder
*R : Read Only Value
0 Y Level
Composite / S-Video - Y Level (ADC
RGB Gain)
10 / 10 0 - 255
Composite / S-Video
* Gain Adjustment [Video]
1 C Level
Composite / S-Video - C Level (ADC
Saturation)
115 / 115 0 - 255 Composite / S-Video
2
3 XCXL Level Cross-Chroma, Cross-Luma Level 3 0 - 5
4 C2DNBANDWIDTH Comb 2D Narrow Bandwidth 3 / 3 0 - 3 NTSC/PAL
5 C2DWBANDWIDTH Comb 2D Wide Bandwidth 4 / 4 0 - 7 NTSC/PAL
6 C2DCNMINLEAK
Comb 2D Chroma Narrow Band
Minimum Leakage
0 / 3 0 - 3
Left Values are adjustable if CXCL
Level = 5.
7 C2DCNSLOPELEAK
Comb 2D Narrow Band Slope
Leakage
7 / 7 0 - 7 NTSC/PAL
8 C2DCWMINLEAK
Comb 2D Wide Band Minimum
Leakage
1 / 3 0 - 3 NTSC/PAL
9 C2DCWSLOPELEAK Comb 2D CW Slope Leakage 6 / 6 0 - 7 NTSC/PAL
10 COMBLEAK2BPGAIN Comb Leak To Ban Pass Gain 1 / 0 0 - 3 NTSC/PAL
11 C2DBDIAGONALGAIN Comb 2D Band Pass Diagonal Gain 1 / 3 0 - 3 NTSC/PAL
12 C2DNBCWBCLGAIN
Comb 2D Narrow Band Comb Wide
Band Comb
1 / 1 0 - 3 NTSC/PAL
13 RLUMASETUP-Enable 7.5IRE Setup Enable 0 0 - 1 Effective only NTSC Signal
Group
40
General
0 IP Mode Sets for IP Off 1 0 - 1
0: IP Block not used
1: IP OFF used with IP Block
1 3:2 PullDown Mode 1 1 - 3
bit0 : Global Motion
bit1 : Video Motion
2 Detect Film Mode Enable 0 0 - 2
0 : 2:3pull down & 2:2pull down
1 : 2:3pull down
2 : 2:2pull down
3 Force IP Mode 2 0 - 2
0 : IP Process Disable
1 : Force Normal IP Mode
2 : Force Film Mode
Effective only for PSF Signal.
Group
41
Deinterlacer setting
Effective only for Progressive ON-L1 mode.
To Next Page
Loading...
Need help?
General