-50-
Electrical Adjustments
Group/
Item
Item Name Function Initial Range Note
4 Cr Imange Area Start X Cr Acquiring Area H-Start Position 500 0-1000
5 Cr Imange Area Start Y Cr Acquiring Area V-Start Position 200 0-1000
6 Image Area H Width Image Level Acquiring Area 8 0-4095
7 Image Area V Hight Image Level Acquiring Area Height 9 0-4095
8 Y Target Level Target Value of Y Level Adj. 217 0-255
9 Cb Target Level Target Value of Cb Level Adj. 212 0-255
10 Cr Target Level Target Value of Cr Level Adj. 212 0-255
11 Gain Tolerance Torelance of Level Adj. 1 0-255
12 Delta Gain Deviation Width of Gain Value 9 0-255
Group
264
Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START
Y - Offset Acquiring Area H-Start
Position
925 0 - 1000
1 Y-OFFSET AREA V START
Y - Offset Acquiring Area V-Start
Position
500 0 - 1000
2
CB - OFFSET AREA H
START
CB - Offset Acquiring Area H-Start
Position
925 0 - 1000
3 CB - OFFSET AREA V START
CB - Offset Acquiring Area V-Start
Position
500 0 - 1000
4
CR - OFFSET AREA H
START
CR - Offset Acquiring Area H-Start
Position
925 0 - 1000
5 CR - OFFSET AREA V START
CR - Offset Acquiring Area V-Start
Position
500 0 - 1000
6 Y - GAIN AREA H START 50 0 - 1000
7 Y - GAIN AREA V START 500 0 - 1000
8 CB - GAIN AREA H START 800 0 - 1000
9 CB - GAIN AREA V START 500 0 - 1000
10 CR - GAIN AREA H START 700 0 - 1000
11 CR - GAIN AREA V START 500 0 - 1000
12 Image AREA H WIDTH YCBCR Level Acquiring Area 13 0 - 4095
13 Image AREA V HIGHT YCBCR Level Acquiring Area Height 9 0 - 4095
14 Y - OFFSET TARTGET 4 0 - 255
15 CB OFFSET TARGET 128 0 - 255
16 CR OFFSET TARGET 128 0-255
17 Y-GAIN TARGET 217 0-255
18 CB-GAINTARGET 237 0-255
19 CR-GAINTARGET 237 0-255
20 OFFSET torelance Torelance of OFFSET Adj. 1 1-255
21 GAIN torelance Torelance of GAIN Adj. 1 1-255
Group
270
CUSTOM(Aspect)
0 Scaler Horizontal Horizontal Scaler Edit 100 68-132
1 Sclaler Vertical Vertical Scaler Edit 100 68-132
2 Connect Seperate/Connect Edit 0 0-1 0:Seperate, 1: Connect
3 Position Horizontal Horizontal Postion Correction 100 85-115
4 Position Vertical Vertical Position Correct 100 85-115
5 Aspect Enable Aspect Adj. Enable 0 0-1 1: Enable, 0: Disable
Group
280
AutoPC Adjust
0 AutoPCAdjustEnable
Auto-PC Adj Operation Enable if Un-
supported Signal Input
0 0-1 0:Enabel, 1:Disable
1 Frequency Step Frequency Steps of Total Dot 1 0-3
2 Frequency Threshold Total Dot Freqency Threshold 5 0-10 0[]<-- - --> 10[Not matched]
3 Fine Phase Do Phase Adj after Total Dot Adj. 1 0-1 0;Excutes Fine Phase; 1:Not Excute
4 BLKDET Black Level Detection Area 1 0 - 3
5 PHASEMSK Phase Detection Filter 0 0 - 3
0: Effective All Bit,
1: Disable Lower 1 bit
2: Disable Lower 2 bit, 3: Disable
Lower 3 bit
Group
290
PanelType * Panel Type Check
0 GammaL/R-View Current Setting Check 0 0-20
0: Gamma for L-Turn
20: Gamma for R-Turn * Read only
1 GammaL/R-Change Setting of Gamma 10 0-20
Sets L-Turn Gamma if the Value is
set to 0.
Sets R-Turn Gamma if the Value is
set to 20.
Group
500
Composite (NTSC) Composite / S-Video
0
To Next Page
Loading...
Need help?
General