Satec PM135P - Page 53

To Next Page

To Previous Page

Chapter 3 Using Front Display Display Operations

PM135 Powermeter Series 53

Phase Current THD, %

Total powers and power factor

Total powers maximum demand export

Total powers maximum demand import

Phase 1 powers and power factor

Phase 2 powers and power factor

Main Page

Default Chapter9
- Table of Contents9
Chapter 1 General Information12
Features12
Available Options14
- Digital I/O14
- Analog Output15
- Additional Communication Port - COM215
- TOU - Battery-Operated Clock Unit15
Customized Options15
- Device Resolution16
- Energy Rollover16
- Display Options16
Measured Parameters16
Chapter 2 Installation19
Site Requirements19
Package Contents19
Mechanical Installation19
- Panel Mounting20
- DIN Rail Mounting20
Electrical Installation22
- Typical Installation22
- Terminals23
- Power Source Connection23
- Voltage Input Connection24
- Current Input Connection24
- Wiring Diagrams25
I/O Connections30
- 4DI/2DO Module30
- DI Module32
- 12DI/4RO Module32
- 4AO Module - Analog Outputs34
- TOU Module - RTC and 4 Digital Inputs34
Communications Connections36
- COM1 RS-485 Connection37
- ETH Module - COM2 Ethernet Connection37
- PRO Module - COM2 PROFIBUS Connection38
- RS-232/422-485 Module - COM2 Connection39
- GPRS/GSM Modem Module - COM2 GPRS Connection40
Chapter 3 Using Front Display41
Display Operations41
- Navigation Buttons42
- Navigating in Data Display Mode43
- Status Indicators43
- Display Features44
Data Displays46
- TEST Mode Data Display46
- Billing Period Data Displays47
- Measurements Maximum Demand Data Display50
- Measurements Data Display51
- Measurements Minimum/Maximum Data Display54
- Measurements Energy Data Display55
- Harmonics Display56
- Waveform Display57
- Phasor Display57
- Digital I/O57
- Device Control Display58
- Basic Settings Display59
- Device Info Display59
- Load Bar Graph59
- Energy Pulse LED60
- Port Activity Leds60
Device Setup61
- Entering the Password61
- Viewing and Changing Setup Options62
Chapter 4 Using PAS Software63
Installing PAS63
Creating a New Site for Your Meter63
Setting up Communications64
- Communicating through a Serial Port65
- Communicating through the Internet66
Setting up the Meter67
- Preparing Setups for the Meter67
- Downloading Setups to the Meter68
- Uploading Setups from the Meter69
Chapter 5 Configuring the PM13571
Configuring Communications71
- Setting up Serial Communication Ports71
- Setting up Ethernet73
- Setting up GPRS Network74
- Setting up Expertpower Client76
- Setting up TCP Notification Client77
General Meter Setup79
- Basic Meter Setup79
- Transformer Correction81
- Device Options82
- Configuring Digital Inputs83
- Configuring Relay Outputs85
- Configuring Analog Outputs86
- Configuring Counters88
- Configuring Alarm/Control Setpoints89
- Configuring the Display93
- Updating the Meter Clock94
- Local Time Settings94
Configuring Meter Security96
Configuring Billing/Tou99
- Configuring Billing/Tariff Registers99
- Configuring the Daily Tariff Schedule101
- Configuring the Season Tariff Schedule101
Configuring Recorders104
- Configuring Meter Memory104
- Configuring the Event Recorder106
- Configuring the Data Recorder106
Configuring Communication Protocols110
- Configuring Modbus110
- Configuring DNP3111
Chapter 6 Device Control and Upgrading114
Resetting Accumulators, Maximum Values and Files114
Viewing and Clearing Device Diagnostics116
Viewing Communication Status and Statistics117
Remote Relay Control117
- Upgrading Device Firmware118
Chapter 7 Monitoring Meters121
Viewing Real-Time Data121
Viewing Real-Time Min/Max Log123
Viewing Real-Time Waveforms124
- Viewing Real-Time Harmonic Spectrum126
Chapter 8 Retrieving and Storing Files129
Uploading Files on Demand129
Using the Upload Scheduler130
Viewing Files On-Line132
Exporting Files132
- Exporting Files in COMTRADE and PQDIF Formats132
- Exporting Files in Excel Format134
Chapter 9 Viewing Files136
Operations with Files136
Viewing Options136
- Customizing Views136
- Working with Tables137
- Working with Graphic Windows138
Viewing the Event Log139
- Viewing the Data Log141
Appendix A Technical Specifications142
Appendix B Analog Output Parameters149
Appendix C Setpoint Triggers and Actions151
Appendix D Parameters for Data Monitoring and Logging154
Appendix E Billing/Tou Profile Log File163
Appendix F Data Scales165
Appendix G Device Diagnostic Codes166
Index167

Satec PM135P - Page 53

Table of Contents

Related product manuals