Secure Care KinderGUARD ID

To Next Page

To Previous Page

Doc. No.: A05280692 Rev. AE ECO: 13200 Date: 11/04/2019

Main Page

Table of Contents2
Section 1 Important Notices7
Please Read this Manual before Beginning the Installation of a Secure Care System7
Section 2 System Block Diagram11
Figure 2-1 System Block Diagram11
Section 3 Power and Grounding Requirements12
Section 4 Typical Installation13
Section 5 Specifications14
Device Electrical Specifications14
Wire Specifications14
Environmental Specifications14
Section 6 Communications System Diagram15
Section 7 Standard Features16
Primary Reset (Escort) Code16
Tertiary Reset (Escort) Code16
Secondary Reset (Programming) Code16
PM Mode16
Loiter Alarm16
Delayed Egress Selectable Timing16
Latching Delayed Egress17
Software Verification17
Section 8 System Component Descriptions18
Kinderguard® ID Exit Panel18
Figure 8-1 Rear View of ID Exit Panel18
Figure 8-2 Front View of Kinderguard ID Exit Panel19
XIU Panel20
Figure 8-3 Rear View of Xiu Panel20
Cutband Receiver21
Figure 8-4 Cutband Receiver Layout21
Section 9 Installation and Connections22
Indoor/Outdoor Remote Keypad Layout22
The Indoor/Outdoor (N/O) Push Button Layout22
Figure 8-5 Rear View of Remote Keypad22
Figure 8-6 Rear View of Push Button22
Basic Installation of Mounting Enclosures23
Figure 9-1 Surface Mount Enclosure23
Figure 9-2 Flush Mount Enclosure24
Remote Annunciation25
Power Supply for Exit Panel26
Figure 9-3 Power Supply Connection26
Data Loop for ID Exit Panel to ID Exit Panel27
Figure 9-4 Data Loop for ID Exit Panel to Xiu Connection27
ID Exit Panel to XIU Connections28
ID Exit Panel to External Receiver Connections29
Figure 9-6 ID Exit Panel to External Receiver Connections29
Second External Receiver Connections30
Figure 9-7 Second Exernal Receiver Connections30
Interfacing the Magnetic Locks to the ID Exit Panel31
Figure 9-8 Magnetic Locks to ID Exit Interface31
Interfacing the Magnetic Solution Locks to the ID Exit Panel32
Figure 9-9 ID Exit Panel to Magnetic Solutions Lock Interface33
Interfacing Two Magnetic Solutions Locks34
Figure 9-10 Interfacing Two Magnetic Solutions Locks34
Interfacing the Push Button and the Remote Keypad35
Delayed Egress and Fire Alarm Connections36
Figure 9-11 Push Button and Remote Keypad Interface36
XIU to Secure Care Software Connections37
Figure 9-12 Delayed Egress and Fire Alarm Connections37
XIU to XIU Connections38
Figure 9-13 Xiu to Secure Care Software Connections38
Figure 9-14 Xiu to Xiu Connection39
Single XIU Connection40
Figure 9-15 Single Xiu Connection40
Cutband Receivers Data Loop41
Figure 9-16 Cutband Receivers Data Loop41
Power Supply for the Cutband Receivers42
Figure 9-17 Power Supply for the Cutband Receivers42
Cutband Receiver Data Connection43
Figure 9-18 Cutband Receiver Data Connection43
Setting the Proper Cutband Receiver ID Code44
Mounting the Cutband Receiver50
Figure 9-19 Mounting the Cutband Receiver50
Programming the STAT ID Exit Panel51
Section 10 Programming Instructions51
Reset Escort Codes51
Escort Time52
Delayed Egress Release Time52
Delayed Egress Activation Time53
Latching Delayed Egress54
Irreversible Latching Delayed Egress54
No Code/ Irreversible Delayed Egress55
Fire Alarm Input Selection55
Enable/Disable the Signal LED55
Latching Fire Alarm56
Locking of Life Safety 101 Features56
Software Version56
Elevator Mode56
Loiter Alarm57
Advanced Security Mode57
Antenna Selection58
Antenna Range Adjustment58
Testing the CAN Bus58
Date Time Change59
PM Mode Feature59
Setting Exit Panel ID Code60
Escort Pendant Enable/Disable60
Defaulting the STAT ID Panel60
XIU Programming61
Section 11 Testing Kinderguard63
ID System with Lock63
Recommended Weekly Testing63
Patient Escort and Anti-Tailgate Feature Test63
Delayed Egress Feature Test63
Remote Keypad Test63
Push Button Test63
Advanced Security Mode Test63
Recommended Monthly Testing63
Fire Alarm Release Feature Test63
Using a Transmitter/System Tester64
Section 12 Troubleshooting65
Section 13 General Product Warranty69
Notices69
Limited Warranty71
Limitations of Liability72
Governing Law and Arbitration72
Severability73
Waiver73
Section 14 Compliance Information73
Appendix A Ul Listing Requirements82
Appendix B Ferrite Placement83
Recommended Ferrite Placement83
Correct and Incorrect Ferrite Installation84
Appendix C 983 Ext. Receiver Kit85
Cutband Receiver Layout86
Appendix D Old Cutband Receiver Layout and Dipswitch Settings86
Cutband Receiver to XIU Connections87
Setting the Proper Cutband Receiver ID Code88
Appendix E Old Pm Programming93
PM Mode Feature93
Display PM Times93
Appendix F 4 Amp Power Supply for Exit Panels94
Appendix G 4 Amp Power Supply for Cutbands95
Power Supply Connections for the Cutband Receiver95
Appendix H California Fire Marshall Listing96

Related product manuals

Secure Care Advantage 500DE

42 pages

Secure Care KinderGUARD ID - Page 81

Table of Contents

Related product manuals