Sensaphone 400 - Page 130

134 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

128

SENSAPHONE 400 User’s Manual

Table of Contents

Default Chapter5
- Important Safety Instructions5
- Fcc Requirements6
- Year Limited Warranty9
- Table of Contents13
Chapter 1: Introduction19
- Feature Summary20
- About this Manual20
- Layout21
- Led Indicators21
- Technical Support22
Chapter 2: Installation23
- Operating Environment23
- Mounting23
- Power Surge Protection23
- Power Supply and Battery Backup24
- Starting the Model 40024
- Run Mode and Standby Mode24
- Telephone Line25
- The Microphone27
- Alert Zones27
- Installing the Sensor28
- Multiple Sensors29
- Outdoor Wiring31
- Disconnecting the Model 400 for Storage or31
  - Seasonal Use31
Chapter 3: Quick Start33
- The Local Keypad33
- Preparation for Programming33
- Quick-Start Programming Steps34
- Summary of the Alarm Dial-Out Process38
Chapter 4: Communications41
Programming41
- Voice Messages41
- The Unit ID Number44
  - Programming the ID Number44
  - Interrogating the ID Number45
- Dial-Out Telephone Numbers45
- Dial-Out Test Mode48
  - To Test a Dialout Phone Number48
  - Manually Dial a Telephone Number48
- Tone or Pulse Dialing49
- Special Dialing49
- Rings until Answer55
  - Programming Rings until Answer55
  - Interrogating Rings until Answer55
- Tad (Telephone Answering Device)56
- Listen-In Time57
  - Programming the Listen-In Time57
  - Interrogating the Listen-In Time58
- Call Delay58
  - Programming the Call Delay59
  - Interrogating Call Delay59
- Local Voice Mute60
  - Enable/Disable Local Voice Mute60
- Voice Repetitions61
  - Programming Voice Repetitions61
  - Interrogating Voice Repetitions61
- Intercall Time62
  - Programming Intercall Time62
  - Interrogating Intercall Time63
- Maximum Number of Calls (Max Calls)64
  - Programming Max Calls64
  - Interrogating Max Calls65
- The Clock65
  - Setting the Clock65
  - Interrogating for the Current Time66
- The Security Code66
  - Locking the Keypad67
  - Unlocking the Keypad67
Chapter 5: Alarm Programming69
- Zone Configuration69
  - Programming Zone Configuration70
  - Interrogating Zone Configuration70
- Enable/Disable Zones71
  - Changing Enabled/Disabled Zone Status71
  - Verifying Enabled/Disabled Zone Status72
- Zone Recognition Time72
  - Programming Zone Recognition Time73
  - Interrogating Zone Recognition Time74
- Establishing High and Low Temperature Limits74
- Temperature Scale77
- Temperature Calibration77
  - Programming Temperature Calibration77
  - Interrogating Temperature Calibration78
- Obtaining Current Temperature79
- Ac Power Monitoring Enable/Disable79
  - Enabling/Disabling the AC Power Alarm79
- Ac Power Failure Recognition Time80
  - Programming Power Failure Recognition Time80
  - Interrogating Power Failure Recognition Time81
- Sound Alarm Monitoring81
Chapter 6: Acknowledgment, Status87
Report & Remote Access87
- Alarm Acknowledgment87
- Status Report89
Chapter 7: Operation97
- Alarm Detection, Dial-Out and Acknowledgment97
- Example: a Dial-Out Telephone Call101
Chapter 8: Controlling the Output103
- Output Modes103
  - To Program the Output Mode104
  - To Play Back the Programmed Output Mode105
- Switching the Output Using the Keypad105
  - Switching the Output over the Phone105
- Typical Applications106
  - Single Thermostat Control106
  - Dual Thermostat Control108
- Controlling Lights or Other Devices110
Appendix A: Weekly Testing111
Procedure111
Appendix B: Troubleshooting113
- Error Messages113
- Communications / Dial out113
- Temperature Monitoring116
- Sound Level Monitoring117
- Other Monitoring118
Appendix C: 400 Quick Reference121
- Parameter Description122
Appendix D: Accessories125
Appendix E: Specifications127
- Alert Zones127
- Microphone127
- Phone Interface127
- LED Indicator127
- Relay Output127
- Power Supply128
- Environmental128
- Physical128
Appendix F: Returning the Unit129
For Repair129
Appendix G: Test Log131