: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 28
Operation/Procedure
1) Enter the number corresponding to the adjustment item with 10-
key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key.
(The set value is stored, and the output corresponding to the set
value is outputted for 30sec.)
Press [CUSTOM SETTINGS] key to stop the operation.
(The main charger grid output voltage adjustment and output check
can be made in each print mode.)
Operation/Procedure
1) Enter the number corresponding to the adjustment item with 10-
key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key.
(The set value is stored, and the voltage corresponding to the set
value is outputted for 30sec.)
Press [CUSTOM SETTINGS] key to stop the operation.
(The transfer output voltage adjustment and output check can be made
in each print mode.)
Item Set range Default
1 AUTO Auto mode 0 - 750 495
2 CHARACTER Text mode
3 MIX Text/Photo mode
4 PHOTO Photo mode
5 PRINTER Printer mode
6 FAX FAX mode
7 PLUS Reverse developing
bias voltage
0 - 250 150
Press [START] key. Press [CUSTOM SETTINGS] key.
Press [START] key. Press [CUSTOM SETTINGS] key.
Or after 30sec output.
8-2
Purpose Adjustment/Operation test/Check
Function
(Purpose)
Used to check and adjust the operation of the main
charger grid voltage in each printer mode and the
control circuit.
Section Image process (Photoconductor/Developing/Transfer/
Cleaning)
Item Set range Default
1 AUTO Auto mode 200 - 1000 580
2 CHARACTER Text mode
3 MIX Text/Photo mode
4 PHOTO Photo mode
5 PRINTER Printer mode
6 FAX FAX mode
SIMULATION 8-1
1
DV BIAS SETTING. SELECT 1-7, AND PRESS START.
1.AUTO 495 2.CHARACTER 495
3.MIX 495 4.PHOTO 495
5.PRINTER 495 6.FAX 495 7.PLUS 150
SIMULATION 8-1
DV BIAS SETTING. INPUT VALUE, AND PRESS START.
1:AUTO (0-750)
495
SIMULATION 8-1
DV BIAS SETTING. EXECUTING···.
1:AUTO
495
Press [START] key. Press [CUSTOM SETTINGS] key.
Press [START] key. Press [CUSTOM SETTINGS] key.
Or after 30sec output.
8-6
Purpose Adjustment/Operation test/Check
Function
(Purpose)
Used to check and adjust the operation of the transfer
voltage and the control circuit.
Section Image process (Photoconductor/Developing/Transfer/
Cleaning)/Transfer
Item
Set
range
Default
AR-M550N/U,
AR-620N/U
AR-M700N/U
1 FRONT Long side print
mode
0 - 800 300 400
2 BACK Back side print
mode
300 400
SIMULATION 8-2
1
MAIN GRID SETTING. SELECT 1-6, AND PRESS START.
1.AUTO 580 2.CHARACTER 580
3.MIX 580 4.PHOTO 580
5.PRINTER 580 6.FAX 580
SIMULATION 8-2
MAIN GRID SETTING. INPUT VALUE, AND PRESS START.
1.AUTO (200-1000)
580
SIMULATION 8-2
MAIN GRID SETTING. EXECUTING···.
1.AUTO
580
1
1
1
Press [START] key. Press [CUSTOM SETTINGS] key.
Press [START] key. Press [CUSTOM SETTINGS] key.
Or after 30sec output.
SIMULATION 8-6
1
THV+ SETTING. SELECT 1-2, AND PRESS START.
1.FRONT 300
2.BACK 300
SIMULATION 8-6
THV+ SETTING. INPUT VALUE, AND PRESS START.
1.FRONT(0-800)
300
SIMULATION 8-6
THV+ SETTING. EXECUTING···.
1.FRONT
300
To Next Page
Loading...
