AR-M550/M620/M700 SIMULATION 8 - 42
Operation/Procedure
1) Select the number corresponding to the counter to be set with 10-
key.
2) Press [START] key.
3) Select the count mode with 10-key.
4) Press [START] key.
Set the count-up (1 or 2) for A3/WLT paper.
(Select the target counter.)
(Count-up)
Operation/Procedure
1) Select the number corresponding to the destination with 10-key.
2) Press [START] key.
After completion of setting, the machine is automatically reset.
Since this simulation cannot change the Fax destination, use SIM 66-2
to change the FAX destination.
Operation/Procedure
1) Select START/END of the network scanner trial mode with 10-key.
2) Press [START] key.
Max. 500 menus can be scanned.
Operation/Procedure
1) Select YES/NO of the toner save mode with 10-key.
2) Press [START] key.
Operation/Procedure
1) Select the number corresponding to the operation mode with 10-
key.
2) Press [START] key.
(Default: 1 for Europe, 0 for the others)
26-5
Purpose Setting
Function
(Purpose)
Used to set the count mode of the total counter and the
maintenance counter.
Section
Item Specifications Counter
1 TOTAL COUNTER Total counter
2 MAINTENANCE (DRUM)
COUNTER
Maintenance counter/ OPC
drum counter
3 DV COUNTER Developer counter
1 1 COUNT UP 1 count-up
2 2 COUNT UP 2 count-up Default
Press [START] key. Press [CUSTOM SETTINGS] key.
26-6
Purpose Setting
Function
(Purpose)
Used to set the specifications (paper, fixed
magnification ratio, etc.) of the destination.
Section
Item Specifications Destination
1 USA United States of America
2 CANADA Canada
3 INCH Inch series EX
4 JAPAN Japan
5 AB_B AB series B5
6 EUROPE Europe
7UK UK
8 AUSTRALIA Australia
9 AB_A AB series A5
10 CHINA China
SIMULATION 26-5
1
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-3, AND PRESS
START.
1. TOTAL COUNTER 1
2. MAINTENANCE(DRUM) COUNTER 1
3. DV COUNTER 1
SIMULATION 26-5
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-2, AND PRESS
START.
1. TOTAL COUNTER
(1: 1COUNT UP, 2: 2COUNT UP)
1
26-10
Purpose Setting
Function
(Purpose)
Used to set the network scanner trial mode.
Section
Item Operation
0 END Trial mode cancel Default
1 START Trial mode start
26-18
Purpose Setting
Function
(Purpose)
Used to set YES/NO of toner save operation. (This
function is valid only in Japan and UK versions.
(Depends on the destination setting of SIM26-6.) For
the other destinations, the same setting can be made
by the user program P22.)
Section
Item Specifications Operation mode
0 YES Toner save mode is set.
1 NO Toner save mode is not set. Default
26-30
Purpose Setting
Function
(Purpose)
Used to set the operation mode conforming to the CE
mark (Europe safety standards). (Conforming to soft
start when driving the fusing heater lamp.)
Section
Item Specifications Operation mode (Common)
0 NO CE mark control NO (Normal operation)
1 YES CE mark control YES (Heater lamp soft start operation)
SIMULATION 26-6
DESTINATION SETUP. SELECT 1-10, AND PRESS START.
1.USA 2.CANADA 3.INCH
4.JAPAN 5.AB_B
6.EUROPE 7.UK 8.AUSTRALIA
9.AB_A 10.CHINA
1
SIMULATION 26-10
NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS
START.
0.END
1.START
1
SIMULATION 26-18
TONER SAVE MODE SETTING. SELECT 0-1, AND PRESS START.
0. YES
1. NO
1
To Next Page
Loading...
