AR-M550/M620/M700 SIMULATION 8 - 51
4) Press P key or [START] key.
The adjustment value is set.
When [START] key is pressed, copying is performed and the
adjustment value is simultaneously set.
Check the density of the printed copy image.
NOTE: When the copy image density is adjusted with this simulation,
the copy image densities of all the copy modes are changed to
the copy image density level set with this simulation.
That is, the copy image density of each copy mode set with SIM
46-9, 10, 11 is changed to the copy image density level
adjusted with this simulation.
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value in
this simulation, the adjustment value is set. When START key
is pressed, the adjustment value is set and copying is per-
formed.
Operation/Procedure
1) Select the number corresponding to the copy density adjustment
level with 10-key. (Select one of 3 - 11.)
2) Press [START] key.
3) Enter the copy density level with 10-key.
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 EXP LEVEL Exposure level selection
3 AE 3.0 AE mode 0 - 99 50
4 CH 3.0 Text mode 3.0
5 MIX 3.0 Text/Photo mode 3.0
6 PHOTO 3.0 Photo mode 3.0
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1 TRAY1 TRAY1
2 TRAY2 TRAY2
3 TRAY3 TRAY3
4 TRAY4 TRAY4
5 BPT Manual feed
6 LCC Side LCC
Select 2, and press [START] key. Press [START] key,
or press [CUSTOM SETTINGS] key.
46-9
Purpose Adjustment
Function
(Purpose)
Used to adjust the print density for each density level
(display value) in the copy mode (binary - Text mode).
An optional print density can be set for each density
level (display value).
Section
Item Picture quality Density
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 EXP LEVEL Exposure level selection
3 1.0 Exposure level 1.0 0 - 99 50
4 1.5 Exposure level 1.5
5 2.0 Exposure level 2.0
6 2.5 Exposure level 2.5
7 3.0 Exposure level 3.0
8 3.5 Exposure level 3.5
9 4.0 Exposure level 4.0
10 4.5 Exposure level 4.5
11 5.0 Exposure level 5.0
SIMULATION 46-2
Select other then 0 - 2, and
press [START] key.
Press [CUSTOM SETTINGS] key.
SIMULATION 46-2
EXP. LEVEL SETUP (2). INPUT VALUE 0-99, AND PRESS START.
3. AE 3.0
Press [START] key.
SIMULATION 46-2
EXP. LEVEL SETUP (2). NOW COPYING.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 1-6, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT 6. LCC
Press [START] key, or
press [CUSTOM SETTINGS] key.
1
Select 0, and
press [START] key.
1
Select 1,
and press
[START] key.
EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. AE 3.0 50 4. CH 3.0 50
5. MIX 3.0 50 6. PHOTO 3.0 50
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 3-6, AND PRESS START.
(EXP. LEVEL SELECT)
3. AE 3.0 4. CH 3.0
5. MIX 3.0 6. PHOTO 3.0
1
To Next Page
Loading...
