AR-M550/M620/M700 SIMULATION 8 - 55
Operation/Procedure
1) Select the number corresponding to one of the following adjust-
ment items with 10-key.
∗ Manual mode (Print density adjustment level)
∗ Auto mode
2) Press [START] key.
3) Enter the print density level with 10-key.
4) Press [P] key or [START] key.
The adjustment value is set.
When [START] key is pressed, printing is perfumed and the adjust-
ment value is set simultaneously.
Check the density of printed image.
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
When the sum of the above set value (1 - 6) and 20 is set, the mode is
changed to the duplex print mode.
NOTE: When [P] key is pressed after entering an adjustment value in
this simulation, the adjustment value is set. When START key
is pressed, the adjustment value is set and copying is per-
formed.
Operation/Procedure
1) Select the number corresponding to one of the following adjust-
ment items with 10-key. (Select one of 3 - 14.)
∗ Normal mode (Print density adjustment level)
∗ Normal mode (Print density adjustment level) (Half-tone mode)
∗ Auto mode
∗ Auto mode (Half-tone mode)
46-13
Purpose Adjustment
Function
(Purpose)
Used to adjust the print density in the FAX mode (each
normal mode). (Only when FAX is installed.)
Section
Item Picture quality
Item
Set
range
Default
0TRAY
SELECT
Paper feed tray selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3 AUTO Auto 0 - 99 50
4 1.0 Exposure level 1
5 2.0 Exposure level 2
6 3.0 Exposure level 3
7 4.0 Exposure level 4
8 5.0 Exposure level 5
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1 TRAY1 TRAY1
2 TRAY2 TRAY2
3 TRAY3 TRAY3
4 TRAY4 TRAY4
5 BPT Manual feed
6 LCC Side LCC
Select 2, and
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
46-14
Purpose Adjustment
Function
(Purpose)
Used to adjust the print density in the FAX mode (each
fine mode). (Only when FAX is installed.)
Section
Item Picture quality
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS
START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0 50 5.2.0 50
6.3.0 50 7.4.0 50 8.5.0 50
50
1
1
Select 1,
and press
[START] key.
Select 0, and press [START] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND
PRESS START.
4.1.0
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). NOW PRINTING.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-6, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE +20:DSPF MODE)
Select other than 0 - 2,
and press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key, or
press [CUSTOM SETTINGS] key.
1
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0 5.2.0
6.3.0 7.4.0 8.5.0
To Next Page
Loading...
