EasyManua.ls Logo

Shelly Wave Plug US - User Manual

Shelly Wave Plug US
28 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Wave Plug US
Z-Wave® smart plug with power measurements
Extended User Guide (EN)
Device: Wave Plug US
USA Part number/Ordering Code: QNPL-001X16US
Z-Wave Product type ID: 0x0002
Z-Wave Product ID: 0x0088
Z-Wave Manufacturer: Shelly Europe
Z-Wave Manufacturer ID: 0x0460

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Shelly Wave Plug US and is the answer not in the manual?

Summary

User and Safety Guide

About the Device

Installation Instruction

Installation instruction

Details the installation of the smart plug for controlling appliances and measuring power.

About Z-Wave

Z-Wave Adding; Removing; Factory reset

Adding the Device to a Z-Wave network (inclusion)

Guides on how to add the device to a Z-Wave network via inclusion.

Adding (inclusion) with the S button

Explains how to add the device to a Z-Wave network using the S button.

Removing the Device from a Z-Wave network (exclusion)

Guides on how to remove the device from a Z-Wave network via exclusion.

Factory reset

Provides instructions for resetting the device to factory default settings.

Z-Wave Security 2 and Device Specific Key (DSK)

Z-Wave DSK label and QR code (example)

LED Signalization

Z-Wave Parameters

Parameter No. 17 - Restore the O (01) state after a power failure

Configures whether the device saves and restores the last ON/OFF state after a power failure.

Parameter No. 19 - O (O1) Auto OFF with timer

Sets a timer for the device to automatically turn OFF the load after a specified period.

Parameter No. 20 - O (O1) Auto ON with timer

Sets a timer for the device to automatically turn ON the load after a specified period.

Parameter No. 23 - O (O1) contact type - NO;NC

Determines the relay contact type for output O (01) as normally open (NO) or normally closed (NC).

Parameter No. 25 - Set timer units to s or ms for O (01)

Specifies whether timers for parameters 19 and 20 use seconds or milliseconds.

Parameter No. 36 - O (O1) Power report on change - percentage

Sets the minimum power change percentage to trigger a report to the gateway.

Parameter No. 39 - Minimum time between reports (O) 01

Determines the minimum time interval between sending power reports to the gateway.

Parameter No. 91 - Water Alarm

Configures the device's response to water alarm notifications.

Parameter No. 92 - Smoke Alarm

Configures the device's response to smoke alarm notifications.

Parameter No. 93 - CO Alarm

Configures the device's response to carbon monoxide (CO) alarm notifications.

Parameter No. 94 - Heat Alarm

Configures the device's response to heat alarm notifications.

Parameter No. 117 - Remote Device reboot

Enables remote rebooting of the device for troubleshooting purposes.

Z-Wave Command Class

Z-Wave Notifications Command class

Z-Wave Associations

Technical Specifications

Shelly Wave Plug US Specifications

General IconGeneral
Power supply120 V ±10 %, 60 Hz
Power consumption< 0.3 W
Power measurement [W]Yes
Max switching voltage AC140 V
Max switching current AC15 A
Overheating protectionYes
Overcurrent protectionYes
Overvoltage protectionYes
Distanceup to 40 m indoors (131 ft.) (Depends on local condition)
Shell materialPlastic
ColorWhite
Z-Wave repeater:Yes
Z-Wave frequencies band(s)908, 4
Maximum radio frequency power transmitted in frequency bend(s)< 25 mW
CPUZ-Wave S800
Compatible socketsNEMA 5-15 (Type-B)
Compatible plugsNEMA 1-15 (Type-A) and NEMA 5-15 (Type-B)
Ambient temperature-20°C to 40°C / -5°F to 105°F
Humidity30% to 70% RH
Max. altitude2000 m / 6562 ft.
Weight and Dimensions IconWeight and Dimensions
Size (H x W x D)38x84x52 ±0.5 mm / 1.5x3.3x2.0 in ±0.02 in
Weight70 ±1 g / 2.47 ±0.04 oz

Related product manuals