2
Contents
Request.......................................................................1
Preface........................................................................1
1. Safety rules.............................................................3
2. Introduction...........................................................3
2-1. Preliminary check......................................................3
(1) Model code check..............................................................4
(2) Accessories check..............................................................4
2-2. Notes on use ..............................................................4
3. Installation and wiring..........................................4
3-1. Installation site (environmental conditions) ..............4
3-2. Mounting...................................................................5
3-3. External dimensions and panel cutout.......................5
3-4. Wiring .......................................................................6
3-5. Terminal layout .........................................................6
3-6. Terminal arrangement table.......................................7
3-7. Operation preparations ..............................................7
4. Names and functions of parts on front panel......8
5. Parameter diagram and setting ...........................9
5-1. Parameter diagram.....................................................9
5-2. Display when power is applied ...............................11
5-3. Switching screens....................................................11
(1) Switching screens within screen group 0 ......................11
(2) Switching between screen group 0 and screen group 1 ...11
(3) Switching screens within screen group 1.........................11
(4) Switching to screen group 2 ............................................12
(5) Switching screens within screen group 2.........................12
(6) Switching to screen group 3 ............................................12
(7) Switching to screen group 4 ............................................12
(8) Switching screens within screen group 4.........................12
(9) Set data modification.......................................................12
5-4. Auto return function................................................13
5-5. Screen group 0 setting .............................................13
(1) Setting target set values (SV) ..........................................13
(2) Manual setting of control output......................................13
(3) Auto tuning (AT) .............................................................14
(4) Standby (STBY) / execution (EXE) ................................15
(5) Event setting....................................................................15
(6) Multi SV (target set values).............................................15
6. Screen explanation and setting items.................16
7. Measuring range codes .......................................23
8. Explanation of functions.....................................24
8-1. Events..................................................................... 24
(1) Alarm action ................................................................... 24
(2) Event standby action selection........................................ 24
(3) Event selection alarm action diagrams ........................... 24
(4) Event status output action............................................... 24
8-2. P.I.D. ...................................................................... 25
(1) P (Proportional action).................................................... 25
(2) I (Integral time) .............................................................. 25
(3) D (Derivative time)......................................................... 25
(4) MR (Manual reset) ......................................................... 25
8-3. Control output ........................................................ 25
(1) Lower limit and higher limit setting limiter.................... 25
(2) Proportional cycling time ............................................... 26
(3) Control output characteristics......................................... 26
8-4. External control input (DI) ..................................... 26
(1) Controller action execution EXE1 (RUN1).................... 26
(2) Controller action execution EXE2 (RUN2).................... 26
(3) Manual output (MAN).................................................... 26
(4) Auto tuning execution (AT) ............................................ 26
(5) SV external selection (ESV2)......................................... 27
(6) Program (PROG)............................................................ 27
(7) Hold signal (HLD).......................................................... 27
(8) Advance (ADV).............................................................. 27
(9) Start pattern external selection 2 bits (PTN2)................. 27
(10) Start pattern external selection 3 bits (PTN3) ............... 27
(11) Total unlatching (L_RS) ............................................... 27
8-9. Soft start ................................................................. 27
(1) Conditions that trigger soft start ..................................... 27
(2) Conditions that cancel soft start...................................... 28
9. Causes and remedy of trouble and errors.........28
9-1. Causes and remedy of trouble ................................ 28
9-2. Causes and remedy of errors .................................. 28
(1) Abnormal measured input............................................... 28
(2) Heater break/loop alarm errors ....................................... 28
10. Parameter setting record ..................................29
11. Specifications .....................................................31
To Next Page
Loading...
