Name: Siemens FC901-U3
Brand: Siemens
Rating: 4 (1 reviews)

To Next Page

To Previous Page

If the FC901 is configured as “Supervisory self restoring”, the system shall return to the

“System Normal” status if the supervisory condition is restored unless there are additional

events on the system. If the FC901 is not configured as “Supervisory self restoring”, the

system reverts to standby condition only after the RESET button is pressed.

Default Chapter4
- Table of Contents4
Introduction8
Control Panel Limitations8
Preface9
FCC Part 68 Warning9
Descriptions11
Fc901 System Description11
- Power Supply11
- Signaling Line Circuit (SLC)12
- Notification Appliance Circuits12
- Serial Interface Circuit12
- Status Relays12
- Programming Port12
- Dact12
Optional Modules12
- City Tie Module (FCI2020-U1)12
- Battery Sets12
- Remote Printer Module (FCA2018-U1)12
Auxiliary Modules13
- Serial LCD Annunciators13
- FT Series LED Driver/Annunciators13
Slc Addressable Devices14
- Smoke Detector14
- Heat Detectors14
- Addressable Modules (Monitor and Control)14
- Manual Stations14
- Sounder Base14
- Programming SLC Devices15
Event History16
General Design Features17
- Environmental17
- Power Limiting17
- Ground Fault Detection17
- NAC Operation17
- Security Features17
Regulatory Standards18
- Underwriters Laboratories18
- Federal Communications Commission18
General Specifications19
- Environmental19
- Primary Power Supply19
- Secondary Power Supply19
- Auxiliary Power Outputs19
- Status Relays20
- Notification Appliance Circuits20
- Serial Interface Circuit20
- SLC Addressable Device Circuits20
- City Tie Circuits20
- DACT Circuits21
Control Panel Operation22
Operation Instructions22
- Standby Condition22
- Alarm Conditions22
- Trouble Conditions23
- Supervisory Conditions23
Additional Operating Procedures25
- Lamp Test25
- History25
Fc901 Operating Instructions26
- Alarm Operation26
- Authorized Personnel Only26
- Trouble Operation26
- Event Scrolling26
- Fuse Replacement and Battery Maintenance26
Fsd901 Operating Instructions27
- Alarm Operation27
- Authorized Personnel Only27
- Trouble Operation27
- Event Scrolling27
- Normal Standby Condition27
Control Panel Installation28
Parts Supplied - Fc90128
- FC901 Enclosure Package28
- FC901 Main Board Package28
  - FC901 Configuration Kit Package29
Cautions30
Control Panel Location30
Installation30
- Enclosure Mounting30
- Remove Knock-Outs33
- Power Supply Mounting34
- Ground Wire Installation35
- Battery Installation36
- Optional City Tie Mounting37
- Main Board Assembly Installation38
- Earth Cable Installation38
System Wiring39
- AC Connection39
- Battery Connection39
Wiring39
- Control Panel Wiring Overview40
- Wiring Entering Enclosure40
- Install Wiring40
- Wiring Separation41
- Internal Structure42
- Power Supply and Battery Wiring43
- Status Relays44
- Auxiliary Power Outputs Wiring44
- NAC Wiring45
- Serial Interface Circuit46
- Serial Remote Device Wiring Overview47
- SLC Addressable Device Circuit48
- SLC Addressable Device Wiring Diagrams49
- Optional City Tie/Leased Line51
- DACT Wiring51
Programming the Control Panel52
Keypad Programming52
Pc Programming52
Programming Security52
Maintenance53
General53
Quick Test54
Appendix-A: Reference Data56
Wire Selection Guides56
- Resistance of Solid Copper Wire56
- Addressable Device Circuit Wire Selection Guide56
Battery Size Calculations57
- System Current Draw Break down57
- SLC Current Draw Break down57
- Battery Size58
Appendix-B: Compatible Devices59
- Devices for Addressable Device Circuits59
- Siemens SLC Manual Pull Stations59
- Siemens SLC Modules59
- Siemens SLC Bases59
- Siemens SLC Accessories59
- 8700 SLC Manual Pull Stations60
- 8700 SLC Detectors60
- 8700 SLC Modules60
- 8700 SLC Bases60
- 8700 SLC Accessories60
- Fd182Ul60
- Global ASA61
- UFP Devices61
Appendix-C: Troubleshooting62
- General62
- System Events62
Appendix-D: Alarm Verification63
Appendix-E: Application Specific Detection64
Appendix-F: Testing/Maintenance65
Appendix-G: Lcd, Controls and Indicators66
- Communication Port Connector66
- LEDS, Buzzer and Dedicated Push Buttons66
- LCD Display69
Appendix-H: Output Features70
- Output Activation- and Deactivation- Delays70
Appendix-I: Pas / Pre-Signal71
- Pas71
- Pre-Signal72
Appendix-J: Dact Information Overview73
Appendix-K: Drift Compensation79
Appendix-L: Glossary80

Siemens FC901-U3 User Manual

Table of Contents

Other manuals for Siemens FC901-U3

Questions and Answers:

Siemens FC901-U3 Specifications

Related product manuals

Brand	Siemens
Model	FC901-U3
Category	Control Panel
Language	English